MAI COMPANY CONFIDENTIAL FIELD INFORMATION BULLETIN SERVICE GROUP(S): MICRO,MINI MFG: MAXTOR NACS TYPE(S): 2190 MFG. MODEL(S): ALL CATEGORY: DISK I/O DESC: FIXED MEDIA *** TABLE OF CONTENTS AS OF 11/10/95 *** FIB 00001.General Information.........................................01/11/94 FIB 00002.Handling Caution when Drive is out of the System............01/21/85 FIB 00003.Formatting 85 MB Maxtor on 2000.............................12/26/85 FIB 00004.Sys 2000 Flaw Maps, DUTIL-Drive Formatting..................08/07/86 FIB 00005.Missing defect maps on MAXTOR drives........................03/31/87 FIB 00006.190 MB (160 MB Formatted) drive available for Basic Four 30004/27/87 FIB 00007.Allow thermal equalization before formatting................04/27/87 FIB 00008.190 MB (169 MB formatted) drive installation on Basic Four 707/07/87 FIB 00009.Adding Maxtor 140 MB disk to 7xxx System....................08/13/87 FIB 00010.NEW JUMPER LOCATIONS ON SCSI ...............................12/12/90 FIB 00011.Jumper.Settings Maxtor 280/380/760/1759 Disk Drives.........07/28/92 FIB 00012.Maxtor 85, 140, 190 ST506 Disk Drives not coming ready......12/13/89 FIB 00013.PART NUMBERS and CAPACITIES FOR MAXTOR DRIVES...............03/19/90 FIB 00014.Installation of M380/M760 Drives on 9XXX and Advanced Series06/26/90 FIB 00015.Maxtor XT-8000SH Series (New 380/760 Models)................08/27/92 FIB 00016.1.503 GB Model P1-17S on MPx & ASx Systems [ WPSF 802 ].....11/11/94 FIB 00017.P1-17S 1.6GB SCSI drive mode sense information for GPx......01/19/95 FIB 00018.Error Formatting Maxtor 7213 Disk Drive with DIVE...........06/23/94 FIB 00019.Formatting Maxtor 7290 SR SCSI Disk w/DIVE on GPx ..........07/22/94 FIB 00020.7213 installation information...............................08/18/94 FIB 00021.LXT-200S GPx40 1.1C dive mode sense information.............10/20/94 FIB 00022.XT-8380S - GPx40 dive mode sense information................10/20/94 FIB 00023.XT-8760S - GPx40 1.1C dive mode sense information...........10/20/94 FIB 00024.LXT-535S - GPx40 DIVE mode sense information................11/19/94 FIB 00025.XT-3280 - GPx40 dive mode sense information.................11/19/94 FIB 00026.7213SR - GPx40 dive mode sense information..................11/19/94 FIB 00027.GPx40 mode sense information for the P1-17S 1.6GB drive.....01/19/95 FIB 00028.MXT 540S - 535MB 3 1/2", Jumper information.................02/05/95 FIB 00029.TERMINATORS FOR 5 1/4" SCSI DRIVES..........................10/23/95 DISK I/O-MAXTOR-ALL---------------------------------Table Of Contents Pg01 of 01 FIB 00001 01/11/94 *** General Information *** *** NACS Machine Types and Feature Numbers *** NACS Type 140MB Maxtor model 1140 - B/4 model 4108 - on a 2000 system .............4120 85MB Maxtor model 1085 - B/4 model 4108 - on a 2000 system ............4171 105MB Maxtor model 1105 - B/4 model 4108 - on a 2000 system ............4186 140MB Maxtor model 1140 - B/4 model 4106 - on a 7X00 system ............4326 160MB Maxtor model 2190 - P/N MM534080 - No NACS type assigned FORM FMT SIZE P/N TYPE HEADS SEC/TRACK CYL BLOCKS FACTOR 71MB MM534070 1085 8 17 1024 138992 5 1/4" 88MB MM534030 1105 11 17 918 171292 5 1/4" 120 MM534040 1140 15 17 918 233580 5 1/4" 160 MM534080 1190 15 17 1224 311610 5 1/4" 320 SCSI MM295100 8380S 8 54 1632 691849 5 1/4" 670 MB SCSI MM295200 8760SH 15 54 1632 5 1/4" 1.6 GB SCSI MM698087 P1-17S 5 1/4" *** Available Documentation *** MAI 2000 5 1/4" Fixed Disk Drive Service Manual BFC number M8083 ORIGINATOR: J.WHALEN MODIFIED by: Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB001 Pg001 FIB 00002 01/21/85 *** Handling Caution when Drive is out of the System *** Original Document Name - Mini Alert 336 The mounting plate studs protrude thruough the shock mounts so that when the drive is placed on a flat surface the studs contact the flat surface and defeat the shock mounting. Under these circumstances it is imperative that all the Winchester Disk Drives be handled with extreme caution, Otherwise either the surface(s) or head(s) may be damaged. ORIGINATOR: J. Sanka DISK I/O-MAXTOR-ALL---------------------------------FIB002 Pg001 FIB 00003 12/26/85 *** Formatting 85 MB Maxtor on 2000 *** Original Document Name - Mini Alert 440 The current level of the diagnostic media (DIA-26.2) shipped with the system 2000 does not contain an entry in the formatter program to format 85 MB Maxtor drives. To format the 85MB Maxtor select the Micropolis 85 MB entry on the menu. ORIGINATOR: J. Van Oordt DISK I/O-MAXTOR-ALL---------------------------------FIB003 Pg001 FIB 00004 08/07/86 *** Sys 2000 Flaw Maps, DUTIL-Drive Formatting *** Original Document Name - Worldwide Product Support Field Bulletin 228 The necessity for keeping and maintaining an up-to-date flaw map for the WDD can not be overemphasized. This holds especially true with possible adaptec firmware problems, where blown formats may necessitate reformatting of the disk unit(s). Some systems may have been shipped without accompanying flaw maps for the disk drives (prior to 3/86). If you have such a system and your unit does not now have a current flaw map, make one at your earliest convience. It is up to you to make sure it can be used as a viable tool. A good format and surface analysis is absolutely essential for reliable operation of the disk unit. The following is suggested - - every disk should have a flaw map. It should include the MFG. list as well as the flaw map printed by the dutil program. - never format a drive unless necessary. You can determine this by running the disk diagnostics, concentrating on the seek tests and using the read- only option. Run the read-only verify option with ecc off to detect possible soft errors. (The error log should also be looked at to determine weak areas of the disk). - If the disk's flaw map is inadvertantly lost, a printout of the defect list can still be obtained by selecting printer command option sp or option lp while running under dutil, and then displaying the defect list. - If the drive has been formatted before and the service rep wishes to format, always use option #5 (update defect map). use option #$4 (format, no surface analysis, defect mapping) only if update defect map fails. Below are listed the various dutil options available; recommended procedures for using them and a concise explanation of what they do. OPTION: 1. Format, surface analysis, defect mapping - use this option to first format a disk unit as if there were no defects, then perform a surface analysis with hardware ecc and retries disabled. After surface analysis, the MFG defects are entered by the user. The surface analysis results are merged with the MFG defects to form a more complete list. (Use this option when no defects are known to exist, or when the defect list is lost). NOTE: Option 1 is the only formatting option which will do 2 formats on the disk; the first without defects, the second with the defect list just created. 2. Format only, no defect mapping - this is the quick format. use this option when no defects are desired, or none are to be mapped out. 3. Surface analysis, report results - surface analysis specifically for use after formatting. This analysis will destroy data on the disk. Use this option after the last formatting option is complete to ensure no further soft errors exist. If defects are found by this option, rerun option #5 to add new defects to flaw map. 4. Format, no surface analysis, defect mapping - this format option is DISK I/O-MAXTOR-ALL---------------------------------FIB004 Pg001 intended to permit the user to enter known defects. This option does not use a previously saved defect list, it is intended primarily to manually enter defects. Option #3 should normally be run after this to ensure that no additional defects exist. 5. Updating defect map - this option is used to add a new defect to the existing defect list created by a previous format. Option #3 should have been run prior to this option. Error log information saved by the o/s is also an excellent source of intermittant bad spots. This option is the only one that uses the saved defect list. Use this option to reformat the disk unit with the old (original) defect list. To do this, simply carriage return when prompted for defects. If no saved defect list exists and no defects are entered, this option informs the user and no formatting will take place. 6. Change disk label - this option only changes the disk label in the superblock. The re-write operation will either take place immediately or during the next formatting process, at the user's option. If the choice is immediate, dutil will create a default label; if the choice is during formatting, the label can be user-defined. 7. Read maxtor defects from disk - only for maxtor disk units which have never been formatted under dutil. Defect list written on the drive by the mfg may be optionally re-written for later dutil use by the user. This eliminates the necessity to manually enter all defects. Do not select this option if the drive has been previously formatted by dutil. To check, use the read-only utilities menu and read defect list. To determine what to do and when, use the following parameters - CONDITION ACTION Maxtor drive never before formatted. option 7 Non-maxtor drive never before formatted and option 4, then option 3 defects are known. Non-maxtor drive never before formatted and option 1 no defects are expected or list is lost. Drive has been formatted before. option 5, then option 3 When defect list on the disk is corrupted. option 4 (enter all defects), then option 3, then option 5 if new defects are found Add a new defect list to an existing list. option 5 Reformat using existing list as a normal option 5 (enter C/R to maintenance procedure. "defect entry" prompt in order to use old list), then option 3, then option 5 if new defects are located To test format and data reliability option 1, read-only utilities The suggested number of surface analysis patterns for use is - as many as time will allow... the more patterns selected, the more thorough the analysis, and the more reliably the unit will operate. DISK I/O-MAXTOR-ALL---------------------------------FIB004 Pg002 ORIGINATOR: P. KOEHLER DISK I/O-MAXTOR-ALL---------------------------------FIB004 Pg003 FIB 00005 03/31/87 *** Missing defect maps on MAXTOR drives *** Surface Defects detected by the manufacturer must be entered at formatting time to prevent read errors during customer operation. Defect Maps on Maxtor Hard Disk drives are supplied in two ways: on a label attached permanently to the drive, or in a sheet of paper shipped with the drive. This sheet is sometimes lost during shipment, installation, etc. To obtain the manufacturer defect list when the sheet of paper containing the manufacturers defect list is missing, proceed as follows: 1. Take note of the Maxtor Model number, and serial number on the Maxtor ID label located at the rear of the drive. 2. Call Basic Four Customer Satisfaction, and ask for WDD Flaw Map for the drive, supply them with the model and serial number. Telephone numbers: Outside California: (800) 848-0600 Inside California: (714) 730-3387 ORIGINATOR: J. VAN OORDT DISK I/O-MAXTOR-ALL---------------------------------FIB005 Pg001 FIB 00006 04/27/87 *** 190 MB (160 MB Formatted) drive available for Basic Four 3000 *** MAI Basic Four is pleased to announce the new 160 Mb disk drive for the MAI 3000 . This is a 5 1/4" disk drive with a 190 Mb disk capacity (UNFORMATTED). This high performance disk drive has 15 data heads, 1 servo head and 8 platters and resembles the currently used 120 Mb drive. The MAI Basic Four part number for this high performance disk drive is: 400575-008. Installation/removal procedures can be found in manual 8083 and are identical to those of the 120MB drive. The following differences should be noted: o Avg. seek time (Buffered) 30 ms vs 27 ms o Max. seek time (Buffered) 54 ms vs 46 ms o # of cylenders 1024 vs 918 ORIGINATOR: C. FIGUEROA DISK I/O-MAXTOR-ALL---------------------------------FIB006 Pg001 FIB 00007 04/27/87 *** Allow thermal equalization before formatting *** When formatting or reformatting any Winchester Disk it is essential for temperature equalization to have been reached before the format is begun. Temperature equalization is the term used to describe the point in time when the disk platter, the read/write heads, and the air temperature within the disk drive housing reach their optimum operating temperature. Should a format procedure be performed on a "cold disk, one or more of the following symptoms may be seen: o hangs of the system causing a warm or cold boot to be performed. o Possible corrupted files o Failure to boot the system at random intervals. In the case of Winchester style disk drives, the following parameters should be met before any attempt to format the disk is begun: o If the drive has been turned off for periods in excess of one hour: Let drive run for a minimum of thirty minutes before attempting to format. o If the drive has been turned off for less than one hour: Let drive run for twenty minutes before formatting. o If drive has been turned off for less than one hour and room temperature is subject to a fluctuation of ten degrees centigrade or more per hour: Let drive run for thirty minutes before formatting. Following the conditions above will assure that the format will have been performed under the same ambient conditions found during normal operation of the system. ORIGINATOR: P. KOEHLER DISK I/O-MAXTOR-ALL---------------------------------FIB007 Pg001 FIB 00008 07/07/87 *** 190 MB (169 MB formatted) drive installation on Basic Four 7X00 *** A new model 4509, 5 1/4" disk drive, 169MB formatted capacity has been added to the MPx 7xxx Series Systems. The user capacity will be less when the drive is setup as a System disk or a Data disk. 4509 Disk type 169MB (M190) 126MB (M140) Track Spacing (TPI) 1022 980 Cylinders 1224 918 Sectors Per Track 9 9 R/W Heads 15 15 Servo Heads 1 1 Disks 8 8 Rotational Speed 3600 RPM 3600 RPM Unformatted Capacity 191.24 MB 143.43 MB Formatted Capacity 169 MB 126 MB Single Track Seek Time 4 MS 5 MS Transfer Rate Mbits/Sec 5 Mbits 5 Mbits MPC SWITCH SETTINGS: 1=Off=Open 0=On=Closed MPC controller: PN 903500 Disk 0 Disk 1 Disk 2 Disk 3 SW4 -1-3-5-7 -2-4-6-8 SW3 -1-3-5-7 -2-4-6-8 M140 1 1 0 1 1 1 0 1 1 1 1 0 1 1 1 0 M190 1 0 1 1 1 0 1 1 0 1 1 1 0 1 1 1 PN 903546 SW3 -1-2-3-4 -5-6-7-8 SW4 -1-2-3-4 -5-6-7-8 M140 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 M190 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 DRIVE ADDRESSING: Disk Drive Control PCB, J7 - (6 5 4 3 2 1) 1 C 2 3 C 4 Disk 0 JMP Disk 1 JMP Disk 2 JMP Disk 3 JMP Notice that "C" must always be jumped (JMP) to a drive number. (Some PCB's have pins marked 123456) Only one selection per drive. DISK DRIVE POWER: Power is supplied to connector J3. The drive requires +5VDC and +12VDC. J3 - Pin 1 = +12VDC Pin 2 = +12VDC Return Pin 3 = +5VDC Return Pin 4 = +5VDC DRIVE ADD-ON: When adding 5 1/4" drives to a system, insure that: DISK I/O-MAXTOR-ALL---------------------------------FIB008 Pg001 1) Only the disk drive at the end of the Bus cable has a terminator resistor pack. All other drives have their terminator pack (U25) removed. ECN #11825A has changed the cabling scheme of the disk drives. Drive 0 should be the drive at the end of the Bus cable. This way when drives are added to the system the need to leap-frog the terminator pack from one drive to another is eliminated. This will also allow proper termination at the END of the Bus cable and not somewhere in the middle. 2) The drive address corresponds to the proper radial port on the MPC controller. 3) Verify proper switch settings OPERATING SOFTWARE LEVEL: The supported OS level for the 4509 169MB disk drive is 8.6. If the 4509 169MB drive is installed on the 8.5 OS level, a dump will occur at load time. The Diagnostic dump 3,11,2,0 - 0,0,0,22 "Probably invalid (unrecognized) device type in device type table...." will complete then continue to the main menu. The drive will not be recognized in Family or NEWX in a Type I load. In Type III load the drive will not be shown as an option to configure. In 8.6 the 4509 M169MB drive will be identified in the following programs as: ROT/ALTTRACKS - "Disk F M169 169Mb" HEADS - "M169 169Mb" NEWX - "M190 Fixed" DCL - "M190" ORIGINATOR: Don Luque DISK I/O-MAXTOR-ALL---------------------------------FIB008 Pg002 FIB 00009 08/13/87 *** Adding Maxtor 140 MB disk to 7xxx System *** SYMPTOM: New disk power supply seems not to work PROBLEM DETERMINATION: Missing sequence cable from ls700 power supply FIX: If only one Maxtor 140 MB disk is on a system, it gets connected to the LS700 power supply in the mainframe. If a second 140 MB disk is added to the system, it gets connected to an additional power supply (MM550140). In order for this new power supply to work, a sequence cable (907039-001) must be connected from J10 of the LS700 to connector PC of the added power supply. This FIB thanx to Ted Morgan of the Rhode Island office. ORIGINATOR: Spencer Schwartz DISK I/O-MAXTOR-ALL---------------------------------FIB009 Pg001 FIB 00010 12/12/90 *** NEW JUMPER LOCATIONS ON SCSI *** THE OEM OF THE SCSI 5 1/4 " FIX DRIVE USED ON THE 94XX SYSTEM HAS REPLACED THE MAIN LOGIC INTERFACE PCBA PN 1012539 WITH AN UPDATED INTERFACE PCBA PN 1014382. THESE BOARDS ARE FORWARD AND BACKWARD COMPATIBLE. JP 2,3,4,5 ___________________________________________________________ | J 3 ^ | | I II I | IIII JP 1 JP6,7 JP 8 | | _______ | I | JP11 ||J 4 | | | IIIII ___________________________________________________________________ ^ | JP 12,13,14,15,16 SCSI ID JP12 JP13 JP14 0 0 0 0 0 = OUT 1 1 0 0 1 = IN 2 0 1 0 3 1 1 0 4 0 0 1 5 1 0 1 6 0 1 1 7 1 1 1 OTHER JUMPER SETTINGS OLD = 1012539 NEW = 1014382 JUMPER MBF SETTING DESCRIPTION OLD / NEW ______________________________________________________ JP-21 /JP1 IN MFG TEST ONLY JP-41 /JP-2 IN " " JP-42 / JP7 OUT IN FOR WRITE PROTECT JP-43 / JP-3 IN MFG TEST ONLY JP-44 / JP-8 IN=GPX/SPX OUT=MPX SPIN UP AT POWER ON JP-81 / JP10 IN DRIVE SUPPLIES TERM POWER JP-82 / JP-9 OUT HOST SUPPLIES TERM POWER JP-83 /JP-12 \ ID0 DEVICE ADD. JP-84 /JP-13 >SEE ID SETTINGS ID1 DEVICE ADD. JP-85 /JP-14 / ID2 DEVICE ADD. JP-86 /JP-15 IN PARITY ENABLE JP-87 /JP-16 IN= MPX OUT=GPX/SPX POWER ON SPIN DELAY JP-91 /JP-4 IN MFG TEST ONLY JP-92 /JP-5 IN " " " JP-93 /JP-6 IN " " " JP-94 /JP-11 IN " " " DISK I/O-MAXTOR-ALL---------------------------------FIB010 Pg001 ORIGINATOR: D LUQUE,J WHALEN DISK I/O-MAXTOR-ALL---------------------------------FIB010 Pg002 FIB 00011 MAI COMPANY CONFIDENTIAL 07/28/92 *** Jumper Settings Maxtor 280/380/760/1759 Disk Drives *** M380/M760 Disk Drive Jumper Settings A. Drive address jumpers MPX GPX JP37 JP36 JP35 Binary Weight Device Address Device Address --------- ---------- --------- ------------- -------------- -------------- Installed Installed Installed 1 1 1 07(Reserved)1 07(Reserved)3 Installed Installed Removed 1 1 0 06 06(Reserved)4 Installed Removed Installed 1 0 1 05 05(Disk 5/GCR)5 Installed Removed Removed 1 0 0 04(Disk 3) 04(Disk 4) Removed Installed Installed 0 1 1 03(Disk 2) 03(Disk 3) Removed Installed Removed 0 1 0 02(Disk 1) 02(Disk 2) Removed Removed Installed 0 0 1 01(Disk 0) 01(Disk 1) Removed Removed Removed 0 0 0 00(Reserved)2 00(Disk 0) 1 SCSI device address 07 is reserved for the DMA-II board. 2 Device address 00 is reserved for SCSI tape drives. 3 SCSI device address 07 is reserved for SSM/SCSC Controller. 4 Device address 06 is reserved for 1/4" SCSI MTCS tape drive. 5 Device address 05 is reserved for Disk 5 or the optional SCSI GCR tape drive(GCR tape drive can not be used when six disk drives are present). B. Miscellaneous Jumpers Jumper Settings Jumper Settings ------- ---------- -------- ---------- ***JP1 Installed JP18 Removed ***JP2 Installed JP26 Removed ***JP3 Installed JP32 Installed ***JP4 Removed JP33 Installed ***JP8 Installed JP34 Removed ***JP9 Installed JP38 Removed JP10 Installed JP39 Installed JP11 Installed JP40 Installed JP14 Installed JP41 Installed JP15 Removed TXD-E19 Installed *** Not on M380. M280 Disk Drive Jumper Settings A. Drive address jumpers SCSI ID JP12 JP13 JP14 ------- ---- ---- ---- 07 In In In 06 Out In In 05 In Out In NOTE: Please have on-hand some spare 04 Out Out In jumpers, may not be in upgrade kit 03 In In Out to change ID. 02 Out In Out 01 In Out Out 00 Out Out Out B. Miscellaneous Jumper Settings DISK I/O-MAXTOR-ALL---------------------------------FIB011 Pg001 OLD=P/N 1012539 / NEW=P/N 1014382 Jumper MBF Setting Description OLD / NEW ----- ----- --------------------------- -----------------------------------. JP-21...JP-1...JUMPER......................MFG TEST ONLY JP-41...JP-2...JUMPER......................MFG TEST ONLY JP-42...JP-7...OPEN........................JUMPER FOR WRITE PROTECT JP-43...JP-3...JUMPER......................MFG TEST ONLY JP-44...JP-8...JUMPER.(In=GPX/SPX Out=MPX).JUMPER FOR SPIN UP AT POWER ON JP-81...JP-10..JUMPER......................JUMPER FOR DRIVE SUPPLIES TERM POWER JP-82...JP-9...OPEN........................JUMPER FOR HOST SUPPLIES TERM POWER JP-83...JP-12..SEE ID SETTINGS.............ID0 JUMPER FOR DEVICE ADDRESS JP-84...JP-13..SEE ID SETTINGS.............ID1 JUMPER FOR DEVICE ADDRESS JP-85...JP-14..SEE ID SETTINGS.............ID2 JUMPER FOR DEVICE ADDRESS JP-86...JP-15. JUMPER......................JUMPER FOR INTERFACE PARITY ENABLE JP-87...JP-16..JUMPER.(In=MPX Out=GPX/SPX).JUMPER FOR POWER ON SPIN DELAY JP-91...JP-4...............................MFG TEST ONLY JP-92...JP-5...............................MFG TEST ONLY JP-93...JP-6...............................MFG TEST ONLY JP-94...JP-11..............................MFG TEST ONLY M1759 Disk Drive Jumper Settings A. Drive Address Register SCSI ID J2-9,10 J2-7,8 J2-5,6 ------- ------- ------ ------ 07 On On On 06 On On Off 05 On Off On 04 On Off Off 03 Off On On 02 Off On Off 01 Off Off On 00 Off Off Off B. Miscellaneous Jumper Settings Jumper Settings Description ------ -------- ------------------------ JP2 Off On=Write protected JP3 Off Factory use only JP4 On1,2 Factory use only JP5 Off On=Slave sync 150 ohms JP6 Off On=Master sync 150 ohms JP8 On1,2 Factory use only JP9 On1,2 Factory use only JP10 Off On=Power supplied pin 26 JP11 On On=Power supplied drive J2-3,4 Off Bus parity disabled J2-1,2 Off Remote LED connection ORIGINATOR: J.O'Brien DISK I/O-MAXTOR-ALL---------------------------------FIB011 Pg002 FIB 00012 12/13/89 *** Maxtor 85, 140, 190 ST506 Disk Drives not coming ready *** SYMPTOM: Drives not coming ready. PROBLEM DETERMINATION: Drives with Controler PCBA's (P/N 1059055) with revision level "L", has a timing problem where the +12 volts will come up befor the +5 volts. Only drives with serial numbers between 5372000 and 5395000, at rev. "L" will display this problem. FIX: A field fix would be to solder a 12 PF capacitor (YY019758) across the leads of R 147. This would now make the 12 PF cap. in parallel with R 147. The drive may also be replaced with a revision below or above "L" (Rev. "L1" is higher than "L"). Revision level will be on metalic Maxtor label on disk drive. ORIGINATOR: J.O'Brien DISK I/O-MAXTOR-ALL---------------------------------FIB012 Pg001 FIB 00013 03/19/90 *** PART NUMBERS and CAPACITIES FOR MAXTOR DRIVES *** TITLE: P/N's For Drives SYMPTOM/TEXT: The following are the part numbers for Maxtor drives used in the MPx, Spx & GPx systems. 85 MB ---------------- MM534070 105 MB --------------- MM534030 140 MB --------------- MM534040 190 MB --------------- MM534080 280 MB SCSI ---------- MM295000 380 MB SCSI ---------- MM295100 . 760 MB SCSI ---------- MM295200 DRIVE CAPACITY (formatted): | Drive | MPx | SPx | other | 1085 --- 71mb 1105 --- 88mb 1140 126mb 120mb (115mb - 1800) 2190 169mb 160mb M280 250mb 245mb M380 364mb 347mb (355mb - GPx) M760 690mb --- ^^^ \ / |____ (Unformatted Cap.) ORIGINATOR: John Tank / D. Loiselle DISK I/O-MAXTOR-ALL---------------------------------FIB013 Pg001 FIB 00014 06/26/90 *** Installation of M380/M760 Drives on 9XXX and Advanced Series *** The M380/M760 SCSI Disk drives are now available for the 9XXX and Advanced series products. These Drives are being marketed as 364MB/690MB drives (usable capacity after formatting) and will be connected to a DMAII pcba in the same manner as the Maxtor 250MB drive. The.target system must be running on O/S level 9.6/10.6G or higher. Drives received in the field will most likely be formatted for the SPx or GPx products which use a sector size of 512, the 9XXX/AS systems require a sector size of 1024. Proceed with the following steps: 1.) Print out 9.6/10.6G version of DIVE documentation from docwriter utility. 2.) Install hardware, see FIB #11 in this section for drive addressing. 3.) Load 9.6/10.6G version of DIVE, make sure all drives show up with correct addresses, select drive # , select STANDARD FORMAT. 4.) Log any errors encountered and until VID information is displayed. 5.) This information must match that in the DIVE documentation from step#1. If it does not, modify the necessary parameters. 6.) If any parameters in step #5 required modification, The Drive MUST be formatted. Otherwise this format operation may be aborted (see note). 7.) If format is performed, be sure to answer YES when asked to write Volume ID. 8.) Test Drive thoroughly with DEMON. 9.) Be sure proper config record is installed on system and proceed with . Drive set up from type 3 load, see MPx hanbook FIB #1 for details. 10.) Test Drive on-line. Note: You may want to format the Drive even though parameters were correct . to test for possible defective tracks caused during shipment. Formatting for the M380 drive takes approx. 11 minutes for initial step (writting of track/sector headers) and approx. 16 minutes for each pattern selected. The M760 takes approximately twice as long. In step #5 above only the parameters proceded by an "*" should be of concern and they are the ones which can be modified. ORIGINATOR: Barry Matthews MODIFIED by: Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB014 Pg001 FIB 00015 MAI COMPANY CONFIDENTIAL 08/27/92 *** Maxtor XT-8000SH Series (New 380/760 Models) *** Maxtor is supplying a new series of drives to replace the XT8380S and XT8760S scsi drives currently used by MAI. The new drives are part of the Maxtor XT-8000SH series. The new drives have a slightly larger unformatted capacity than the ones MAI has been using, however, they will be formatted to the same capacity as before. The new drives can be identified by the addition of an H to the end of the model number: XT-8760SH = new version 760MB XT-8380SH = new version 380MB These drives have different PCBA layout and jumpering. Use the following figure and tables to locate and configure the jumpers. Jumper Configurations: XT-8000SH PCBA # 1023035 and # 1023900 ______________________________________________________________ | |J | |__|3 | | __ JP40 | | | |J JP1 | | |1_|2 JP14 | | __ JP2 | | | |J JP38 | | |__|6 JP3 | |__ | __| J J | | | . P P | | | | JP 4 5 | |J | . 18 | |1 | | | | | . JP JP JP6 JP7 | | | | 34 41 | | | _____________ | |__|______________________| |_______________________| . NOTE: Terminators are shown as | in this figure. The period (".") indicates pin 1 orientation. (continued on next page) DISK I/O-MAXTOR-ALL---------------------------------FIB015 Pg001 JUMPER TABLE JUMPER MAI DEFAULT DESCRIPTION ------ ----------- ------------------------------- JP1 - OPEN - JP2 - OPEN - JP3 - IN - JP4 - OPEN - MANUFACTURING USE JP5 - IN - MANUFACTURING USE JP6 - OPEN - MANUFACTURING USE JP7 - IN - MANUFACTURING USE JP10 - - MANUFACTURING USE JP11 - - MANUFACTURING USE JP14 - IN - SPIN WITH POWER JP15 - - MANUFACTURING USE JP18 - OPEN - DISABLE WRITE PROTECTION OPTION JP26 - - MANUFACTURING USE JP34 - OPEN - TERMINATION POWER JP38 - OPEN - SPIN DELAY OPTION JP39 - - MANUFACTURING USE JP40 - IN - PARITY ENABLED JP41 - IN - TERMINATION POWER SCSI ID - J2 JUMPERS -------------------------------------- | SCSI | PRIORITY | PINS | PINS | PINS | | ID | | 1-2 | 3-4 | 5-6 | |------|----------|------|------|------| | 0 | lowest | OUT | OUT | OUT | | 1 | : | OUT | OUT | IN | | 2 | : | OUT | IN | OUT | | 3 | : | OUT | IN | IN | | 4 | : | IN | OUT | OUT | | 5 | : | IN | OUT | IN | | 6 | : | IN | IN | OUT | | 7 | highest | IN | IN | IN | |______|__________|______|______|______| ORIGINATOR: Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB015 Pg002 FIB 00016 MAI COMPANY CONFIDENTIAL 11/11/94 *** 1.503 GB Model P1-17S on MPx & ASx Systems [ WPSF 802 ] *** Type: Informational With the release of the M.7B OS, a 1.4 Gigabyte (GB) disk drive is now available for the MPx 9xxx and ASxx series systems. Support: The 1.4GB drive requires the following for support: o M.7B*03 OS level o MPx 9xxx or ASxx series system o DMA-II, -002 version Specifications: The 1.4GB (MAXTOR P1-17S) specifications are as follows: DRIVE ID: P1-17S DRIVE TYPE: Fixed 5-1/4 inch SCSI RAW FORMAT CAPACITY: 1.503 Gbytes BYTES/SECTOR: 1024 SECTORS/TRACK: 54 DATA HEADS: 19 SERVO HEADS: 1 CYLINDERS: 1778 (See Note) AVERAGE SEEK TIME: 13 mseconds BUS TRANSFER RATE: 2.5 - 3.6 Mbytes/second PART NUMBER: 916948-001 NOTE: DIVE/NEWX indicates 1520 Cylinders, which reflect Logical Sectors, that is based on 54 sectors per track. The drive uses 'zones' so the actual sectors per track differ per zone. Jumpers: The following is a list of the jumpers and their settings: JUMPER / SETTING JUMPER / SETTING JUMPER / SETTING JP1 IN JP7 IN JP12 IN JP3 OUT JP8 IN 1-2 JP13 OUT JP4 IN 1-2 JP9 IN 1-2 J2, 1 thru 6 see SCSI ID JP5 OUT JP10 OUT J2, 7-8 OUT JP6 OUT JP11 IN J2, 9-10 OUT SCSI ID settings are achieved by jumping 'paired' pins on J2. J2-1,2(4) J2-3,4(2) J2-5,6(1) BINARY WEIGHT DEVICE ADDRESS . OUT OUT OUT 0 0 0 00 <(MCTS MAY HAVE OUT OUT IN 0 0 1 01 THIS ID) OUT IN OUT 0 1 0 02 OUT IN IN 0 1 1 03 IN OUT OUT 1 0 0 04 IN OUT IN 1 0 1 05 IN IN OUT 1 1 0 06 IN IN IN 1 1 1 07 <(RESERVED FOR DMA-II PCBA) DISK I/O-MAXTOR-ALL---------------------------------FIB016 Pg001 J3 J2 J6 J1 ____ _________ _________________________ |oooo| |: : : : :| : |:::::::::::::::::::::::::| <- COMPONENT ------------------------------------------------------- SIDE | ^ ^ ^ ^ ^ ^| <- HDA | 10 | | 1 1 50| <- PIN #'S | 1 2 4 <- BINARY WEIGHT, SCSI ID | DISPLAY OF 1.4GB SCSI ID LOCATION DIVE: With the high density of the 1.4GB disk drive, formatting of the drive can take up to 11 hours if all 9 passes are used ! With the state-of-the-art technology used in the 1.4GB disk drive, only 1 pass of DIVE is required which take's up to 1.5 hours. Refer to the DIVE docwriter file or the REFERENCE-BASIC FOUR-DOCWRITER-DIVE FIB 6 for instructions MODE SENSE PARAMETERS FOR P1-17S (on MPx/ASx systems) Unit Number: 36 Device Type : 10 Variance : 32 Id Revision: 8.7.10.1 Date Written: Time Written: Disk Name:*?????????? Vendor Id:#MBF-DISK Product Id:#P1-17S Product Rev.:#00000000 Num of Cylinders:*1520 Descriptor Fields:#1 0 0 19 54 1519 1 0 Number of Heads :*19 Fmt Sector Cap. : 1559520 Blocks per Track:*54 Last Track Sec. 0: 1560026 Bytes per Block :*1024 Usable Sectors :#1560080 Raw Block Cap. :#1824228 Usable Blocks :#1560081 Mode Sense/Select Pages:#7800 Drive Mode Page 1: 2100 OS Default: 2500 Format Gap 1:#0 Gap 2:#0 Step Rate/2-byte :#0 Interleave:#1 Write Precomp Cylinder :#0 Number of Tracks per Zone :*19 Landing Zone Cylinder :#0 Alternate Tracks per Zone :#0 Reduced Write Curnt Cyl:#0 Alternate Sectors per Zone :*6 Verify-by-Bytes :#F Alternate Tracks per Volume:*0 SCSI Commands:D9B0273E04B101180000000000000000000000000000000000000000 Note: * = changeable field # = not changeable for this drive type INSTALLATION: The installation of the 1.4GB disk drive is the same as any other SCSI disk drive that MAI Systems offers. Installation guidelines are as follows: o OS level of M.7B*03 o DMA-II, version -002. Insure that the fuse on the DMA-II is good. o The End Connector on the SCSI Bus has the SCSI device with the SCSI Bus Terminators and Terminators installed correctly. No other SCSI device on that bus will have terminators. o Power Connections for the DC power at the disk drive and all the way through to the power source, have good pin contact connections. If the DC power source is the LS700 power supply, check the connection at the adapter on the LS700 bus bars and the screws that attach the adapter to the bus bars. o Each SCSI device on the same SCSI Bus have different SCSI ID's. DISK I/O-MAXTOR-ALL---------------------------------FIB016 Pg002 DOCUMENTS: Addendum to the MPx/ASxx manual, M82422B (008242-002). DOCWRITER Dive. ORIGINATOR: Don Luque DISK I/O-MAXTOR-ALL---------------------------------FIB016 Pg003 FIB 00017 MAI COMPANY CONFIDENTIAL 01/19/95 *** P1-17S 1.6GB SCSI drive mode sense information for GPx *** Following are the recommended critical mode sense parameter values for the Maxtor 1.6 Gigabyte SCSI disk drive. In order to ensure the proper operation of a system with a Maxtor P1-17 drive (the 1.6 Gigabyte 5 1/4" SCSI drive), several fields located in the Page 1 and Page 3 (the Error Recover Parameters Page and the Format Parameters Page respectively) should be set to predetermined values. The following table lists the fields that need to be modified and their recommended values : Error Recovery Parameters Page FIELD VALUE (decimal) Write Reallocation Bit...................0 Read Reallocation Bit....................0 Transfer Block Bit.......................1 Read Continuous Bit......................0 Early Error Correction Bit...............0 Post Error Bit...........................1 Disable Transfer on Error Bit............0 Disable Correction Bit...................0 RetryCount...............................14 Format Parameters Page FIELD VALUE (decimal) Data Bytes per Physical Sector...512 The following steps should be taken in order to ensure that the above listed fields have the proper values : Step 1 - Boot DIVE. Step 2 - Select the "FORMAT" option Step 3 - Select the "NON-STANDARD FORMAT" option. Step 4 - Select the "EDIT MODE SENSE DATA" option. Step 5 - Change byte 14 to 24 hex, byte 15 to 0E hex and so on according to the following table : BYTE NUMBER VALUE 14........24 15........0e 52........02 53........00 Step 6- Select the "BEGIN FORMATTING THE DISK" option. The disk will now be formatted with the correct mode sense values. NOTE: Refer to FIB 27 for a listing of all mode sense parameters. ORIGINATOR: Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB017 Pg001 FIB 00018 MAI COMPANY CONFIDENTIAL 06/23/94 *** Error Formatting Maxtor 7213 Disk Drive with DIVE *** Subject: Maxtor 7213 disk drives on GPx 30/40/50 Author : Dale Jensen Type : Problem/Informational Date : 6/22/94 Purpose: To inform the field of a formatting problem on the Maxtor 7213 disk drive. Details: The Maxtor LXT213 disk drive, which is used on GPx 30/40/50 Series is no longer available. In their place, we are shipping the Maxtor 7213 disk drive. Attempting to do a "standard format" or "non-standard format" (using dive) with the default parameters will result in the drive returning the following status and not formatting : A sense key of hex 5 and a sense code of hex 26 (the drive does not like a field in the parameter list) Use the following procedure with dive to format the Maxtor 7213 disks on GPx 30/40/50 systems. Under the 'Format' menu, select 'Non-Standard Format'. Then select the 'edit format parameters' option. At the bottom of the screen dive asks: "Are these entries correct (Y/N)?" Enter "N" and the cursor will move to the top of the screen. Enter "0" after the entry "FmtDat" and then 'CR' for the next (8) lines. At the bottom of the screen dive asks: "Are these entries correct (y/n)?" Enter "y". At this point you will return to the menu for 'Non-Standard Format' and you can choose option #4 to begin formatting. The disk should then format correctly using the vendor's default parameters. ORIGINATOR: Dale Jensen DISK I/O-MAXTOR-ALL---------------------------------FIB018 Pg001 FIB 00019 MAI COMPANY CONFIDENTIAL 07/22/94 *** Formatting Maxtor 7290 SR SCSI Disk w/DIVE on GPx *** Purpose: To give the steps format the Maxtor 7290SR SCSI disk drive using DIVE on GPx Series 30/40/50. Do the following: Boot DIVE Select FORMAT Under the FORMAT menu select NON-STANDARD FORMAT Under Non-standard format select EDIT FORMAT PARAMETERS You will be prompted: "Are these entries correct (Y/N)?" Enter "N". The cursor will move to the top of the screen. Enter "0" after the entry "FmtDat" Enter on the next 5 lines. Enter "N" after the entry "Issue MODE SELECT" Enter for the next 2 lines. You will be prompted: Are the entries correct (Y/N)? Enter "Y" You will return to the menu for NON-STANDARD FORMAT Select choice #4 (Begin Formatting the Disk) ORIGINATOR: Dan Arteritano DISK I/O-MAXTOR-ALL---------------------------------FIB019 Pg001 FIB 00020 MAI COMPANY CONFIDENTIAL 08/18/94 *** 7213 installation information *** SUBJECT : Maxtor 7213 drive field information TYPE : Informational PURPOSE : To provide the field with information needed for installation of the Maxtor 7213 disk drive. DETAILS : The Maxtor LXT213 disk drives used in the gpx 30/40/50 series systems are no longer available and the Maxtor 7213 disk drive is being shipped in its place. General specifications and jumper settings are provided below. BASIC SPECIFICATIONS FORMATTED CAPACITY 213MB CYLINDERS 1,690 DATA HEADS 4 DISKS 2 ON-BOARD CACHE 64K AVG. SEEK TIME 15ms BASIC INSTALLATION STEPS DRIVE IS SHIPPED WITH AN ID OF 6 TO PROVIDE SPARE JUMPERS. CHOOSE ADDRESS JUMPERS ACCORDING TO SPECIFIC INSTALLATION REQUIREMENTS. THE LAST PHYSICAL DEVICE ON THE SCSI BUS MUST BE TERMINATED. INSTALL 50-PIN RIBBON CONNECTOR AND DC POWER CONNECTOR. 7213S JUMPER FUNCTIONS JUMPER FUNCTION AS SHIPPED FROM MAXTOR J301 TERMINATOR POWER INSTALLED J302 POWER-UP OPTION INSTALLED J303 DISABLE PARITY REMOVED J304 RESERVED REMOVED J305 RESERVED REMOVED J306 RESERVED REMOVED J307 TARGET ID ADDRESS(MSB) INSTALLED J308 TARGET ID ADDRESS INSTALLED J309 TARGET ID ADDRESS(LSB) REMOVED DRIVE ADDRESSING SCSI ID PRIORITY J307 J308 J309 0 LOWEST O O O 1 O O J 2 O J O 3 O J J 4 J O O 5 J O J 6 J J O 7 HIGHEST J J J As shipped, the only jumpers that may require changes are for terminator power and drive addressing. There are also 2 ten pin SIPs (resistor networks) installed on the drive when shipped. These SIPs must be removed if the drive is not DISK I/O-MAXTOR-ALL---------------------------------FIB020 Pg001 the SCSI termination device. ORIGINATOR: Dale Jensen DISK I/O-MAXTOR-ALL---------------------------------FIB020 Pg002 DISK I/O-MAXTOR-ALL---------------------------------FIB020 Pg002 FIB 00021 MAI COMPANY CONFIDENTIAL 10/20/94 *** LXT-200S GPx40 1.1C dive mode sense information *** The later versions of dive do not display the drive mode sense parameters in the same manner as earlier versions, following is a series of screens from 1.1C dive on a GPx40, for a working Maxtor LXT-200S drive. MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== ERROR RECOVERY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Auto Write Reallocation Enabled Bit 0 0 0 0 Auto Read Reallocation Enabled Bit 0 0 0 0 Transfer Block Bit 0 0 0 1 Read Continuous Bit 0 0 0 1 Early Error Correction Bit 0 0 0 1 Post Error Bit 0 0 0 1 Disable Transfer on Error Bit 0 0 0 1 Disable Correction Bit 0 0 0 1 Correction.Span 11 11 11 ff Head Offset Count 0 0 0 0 Retry Count 8 8 8 ff Data Strobe Offset Count 0 0 0 0 Recover Limit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DISCONNECT/RECONNECT CONTROL PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Buffer Full Ratio 16 16 16 ff Buffer Empty Ratio 64 64 64 ff Bus Inactivity Limit 0 0 0 0 Disconnect Time Limit 0 0 0 0 Connect Time Limit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DEVICE FORMAT PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Tracks per Zone 1 1 1 0 Alternate Sectors per Zone 1 1 1 ffff Alternate Tracks per Zone 0 0 0 0 Alternate Tracks per Volume 7 7 7 0 Sectors per Track 42 42 42 0 Data Bytes per Physical Sector 512 512 512 ffff Interleave 1 1 1 0 Track Skew 1 1 1 0 Cylinder Skew 21 21 21 0 DISK I/O-MAXTOR-ALL---------------------------------FIB021 Pg001 Soft Sector Format Bit 0 0 0 0 Hard Sector Format Bit 1 1 1 0 Removeable Media Bit 0 0 0 0 Surface Bit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DRIVE GEOMETRY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Maximum Number of Cylinders 1314 1314 1314 ffff Maximum Number of Heads 7 7 7 ff Start Cyl - Write Precompensation 0 0 0 0 Start Cyl - Reduced Write Current 0 0 0 0 Drive Step Rate 0 0 0 0 Landing Zone Cylinder 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== CACHE PAGE PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Write Cache Enable Bit 0 0 0 0 Multiplication Factor 0 0 0 0 Read Cache Disable 0 0 0 1 Demand Read Retension Priority 1 1 1 f Write Retension Priority 1 1 1 f Disable Pre-fetch Transfer Length 65471 65471 65471 ffff Minimum Pre-fetch 0 0 0 ffff Maximum Pre-fetch 64 64 64 ffff Maximum Pre-fetch Ceiling 64 64 64 ffff MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT FORMAT PARAMETERS FORMAT-UNIT Command Block Bits FmtDat 1 CmpLst 0 Defect Header Parameters FOV 1 DPRY 0 DCRT 1 . STPF 1 DIVE Format Options Issue MODE SELECT Y Surface Analysis Y Use Edited G-List N MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DISK I/O-MAXTOR-ALL---------------------------------FIB021 Pg002 EDIT SENSE DATA BYTE HEX BINARY COMMENT 0 00 0 0 0 0 0 0 0 0 Parameter List Header 1 00 0 0 0 0 0 0 0 0 2 00 0 0 0 0 0 0 0 0 . 3 08 0 0 0 0 1 0 0 0 4 00 0 0 0 0 0 0 0 0 Block Descriptor 5 05 0 0 0 0 0 1 0 1 6 fb 1 1 1 1 1 0 1 1 7 77 0 1 1 1 0 1 1 1 . 8 00 0 0 0 0 0 0 0 0 9 00 0 0 0 0 0 0 0 0 10 02 0 0 0 0 0 0 1 0 . 11 00 0 0 0 0 0 0 0 0 12 01 0 0 0 0 0 0 0 1 Page 1 Start MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 13 06 0 0 0 0 0 1 1 0 Page Length : 6 bytes 14 00 0 0 0 0 0 0 0 0 15 08 0 0 0 0 1 0 0 0 16 0b 0 0 0 0 1 0 1 1 17 00 0 0 0 0 0 0 0 0 18 00 0 0 0 0 0 0 0 0 19 00 0 0 0 0 0 0 0 0 20 02 0 0 0 0 0 0 1 0 Page 2 Start 21 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes . 22 10 0 0 0 1 0 0 0 0 23 40 0 1 0 0 0 0 0 0 24 00 0 0 0 0 0 0 0 0 25 00 0 0 0 0 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 26 00 0 0 0 0 0 0 0 0 27 00 0 0 0 0 0 0 0 0 28 00 0 0 0 0 0 0 0 0 29 00 0 0 0 0 0 0 0 0 30 00 0 0 0 0 0 0 0 0 31 00 0 0 0 0 0 0 0 0 32 03 0 0 0 0 0 0 1 1 Page 3 Start 33 16 0 0 0 1 0 1 1 0 Page Length : 22 bytes 34 00 0 0 0 0 0 0 0 0 35 01 0 0 0 0 0 0 0 1 36 00 0 0 0 0 0 0 0 0 37 01 0 0 0 0 0 0 0 1 38 00 0 0 0 0 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DISK I/O-MAXTOR-ALL---------------------------------FIB021 Pg003 EDIT SENSE DATA BYTE HEX BINARY COMMENT 39 00 0 0 0 0 0 0 0 0 40 00 0 0 0 0 0 0 0 0 41 07 0 0 0 0 0 1 1 1 42 00 0 0 0 0 0 0 0 0 43 2a 0 0 1 0 1 0 1 0 44 02 0 0 0 0 0 0 1 0 45 00 0 0 0 0 0 0 0 0 46 00 0 0 0 0 0 0 0 0 47 01 0 0 0 0 0 0 0 1 . 48 00 0 0 0 0 0 0 0 0 49 01 0 0 0 0 0 0 0 1 50 00 0 0 0 0 0 0 0 0 51 15 0 0 0 1 0 1 0 1 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 52 40 0 1 0 0 0 0 0 0 53 00 0 0 0 0 0 0 0 0 54 00 0 0 0 0 0 0 0 0 . 55 00 0 0 0 0 0 0 0 0 56 04 0 0 0 0 0 1 0 0 Page 4 Start 57 12 0 0 0 1 0 0 1 0 Page Length : 18 bytes 58 00 0 0 0 0 0 0 0 0 59 05 0 0 0 0 0 1 0 1 60 22 0 0 1 0 0 0 1 0 61 07 0 0 0 0 0 1 1 1 62 00 0 0 0 0 0 0 0 0 63 00 0 0 0 0 0 0 0 0 64 00 0 0 0 0 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 65 00 0 0 0 0 0 0 0 0 . 66 00 0 0 0 0 0 0 0 0 67 00 0 0 0 0 0 0 0 0 68 00 0 0 0 0 0 0 0 0 69 00 0 0 0 0 0 0 0 0 70 00 0 0 0 0 0 0 0 0 71 00 0 0 0 0 0 0 0 0 72 00 0 0 0 0 0 0 0 0 73 00 0 0 0 0 0 0 0 0 74 00 0 0 0 0 0 0 0 0 75 00 0 0 0 0 0 0 0 0 76 08 0 0 0 0 1 0 0 0 Page 8 Start 77 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA DISK I/O-MAXTOR-ALL---------------------------------FIB021 Pg004 BYTE HEX BINARY COMMENT 78 00 0 0 0 0 0 0 0 0 79 11 0 0 0 1 0 0 0 1 80 ff 1 1 1 1 1 1 1 1 . 81 bf 1 0 1 1 1 1 1 1 82 00 0 0 0 0 0 0 0 0 83 00 0 0 0 0 0 0 0 0 . 84 00 0 0 0 0 0 0 0 0 85 40 0 1 0 0 0 0 0 0 86 00 0 0 0 0 0 0 0 0 87 40 0 1 0 0 0 0 0 0 ORIGINATOR: Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB021 Pg005 FIB 00022 MAI COMPANY CONFIDENTIAL 10/20/94 *** XT-8380S - GPx40 dive mode sense information *** The later levels of GPx40 dive display the mode sense information in a different manner from the earlier levels of dive. Following is a series of screens from 1.1C dive on a working Maxtor XT-8380S drive. Selected Device : 0s0 ERROR RECOVERY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Auto Write Reallocation Enabled Bit 0 0 0 1 Auto Read Reallocation Enabled Bit 0 0 0 1 Transfer Block Bit 1 0 1 1 Read Continuous Bit 0 0 0 1 Early Error Correction Bit 0 0 0 1 Post Error Bit 1 0 1 1 Disable Transfer on Error Bit 0 0 0 1 Disable Correction Bit 0 0 0 1 Correction Span 12 12 12 3f Head Offset Count 0 0 0 ff Retry.Count 8 16 8 ff Data Strobe Offset Count 0 0 0 0 Recover Limit 255 255 255 0 .............................................................................. Selected Device : 0s0 DISCONNECT/RECONNECT CONTROL PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Buffer Full Ratio 0 0 0 ff Buffer Empty Ratio 0 0 0 ff Bus.Inactivity Limit 10 10 10 ffff Disconnect Time Limit 0 0 0 0 Connect Time Limit 0 0 0 0 .............................................................................. Selected Device : 0s0 DEVICE FORMAT PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Tracks per Zone 8 8 8 ffff Alternate Sectors per Zone 5 5 5 ffff Alternate Tracks per Zone 0 0 0 0 Alternate Tracks per Volume 24 24 24 ffff Sectors per Track 54 54 54 ffff Data Bytes per Physical Sector 512 512 512 ffff Interleave 1 1 1 0 Track Skew 0 0 0 ffff Cylinder.Skew 16 65535 16 ffff Soft Sector Format Bit 0 0 0 0 Hard Sector Format Bit 1 1 1 0 DISK I/O-MAXTOR-ALL---------------------------------FIB022 Pg001 Removeable Media Bit 0 0 0 0 Surface Bit 0 0 0 0 .............................................................................. Selected Device : 0s0 DRIVE GEOMETRY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Maximum Number of Cylinders 1632 1632 1632 ffffff Maximum Number of Heads 8 8 8 ff Start Cyl - Write Precompensation 0 0 0 0 Start Cyl - Reduced Write Current 0 0 0 0 Drive Step Rate 0 0 0 0 Landing Zone Cylinder 0 0 0 0 .............................................................................. Selected Device : 0s0 CACHE PAGE PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Write Cache Enable Bit 0 0 0 0 Multiplication Factor 0 0 0 0 Read Cache Disable 1 1 1 1 Demand Read Retension Priority 0 0 0 0 Write Retension Priority 0 0 0 0 Disable Pre-fetch Transfer Length 65535 65535 65535 0 Minimum Pre-fetch 0 0 0 0 Maximum Pre-fetch 89 89 89 0 Maximum Pre-fetch Ceiling 0 0 0 0 .............................................................................. Selected Device : 0s0 EDIT SENSE DATA BYTE HEX BINARY COMMENT 0 00 0 0 0 0 0 0 0 0 Parameter List Header 1 00 0 0 0 0 0 0 0 0 2 00 0 0 0 0 0 0 0 0 . 3 08 0 0 0 0 1 0 0 0 4 00 0 0 0 0 0 0 0 0 Block Descriptor 5 00 0 0 0 0 0 0 0 0 6 00 0 0 0 0 0 0 0 0 7 00 0 0 0 0 0 0 0 0 . 8 00 0 0 0 0 0 0 0 0 9 00 0 0 0 0 0 0 0 0 10 02 0 0 0 0 0 0 1 0 . 11 00 0 0 0 0 0 0 0 0 12 01 0 0 0 0 0 0 0 1 Page 1 Start .................................................. Selected Device : 0s0 EDIT SENSE DATA DISK I/O-MAXTOR-ALL---------------------------------FIB022 Pg002 BYTE HEX BINARY COMMENT 13 06 0 0 0 0 0 1 1 0 Page Length : 6 bytes 14 24 0 0 1 0 0 1 0 0 15 08 0 0 0 0 1 0 0 0 16 0c 0 0 0 0 1 1 0 0 17 00 0 0 0 0 0 0 0 0 18 00 0 0 0 0 0 0 0 0 19 ff 1 1 1 1 1 1 1 1 20 02 0 0 0 0 0 0 1 0 Page 2 Start 21 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes . 22 00 0 0 0 0 0 0 0 0 23 00 0 0 0 0 0 0 0 0 24 00 0 0 0 0 0 0 0 0 25 0a 0 0 0 0 1 0 1 0 ............................................................................... Selected Device : 0s0 EDIT SENSE DATA BYTE HEX BINARY COMMENT 26 00 0 0 0 0 0 0 0 0 27 00 0 0 0 0 0 0 0 0 28 00 0 0 0 0 0 0 0 0 29 00 0 0 0 0 0 0 0 0 30 00 0 0 0 0 0 0 0 0 31 00 0 0 0 0 0 0 0 0 32 03 0 0 0 0 0 0 1 1 Page 3 Start 33 16 0 0 0 1 0 1 1 0 Page Length : 22 bytes 34 00 0 0 0 0 0 0 0 0 35 08 0 0 0 0 1 0 0 0 36 00 0 0 0 0 0 0 0 0 37 05 0 0 0 0 0 1 0 1 38 00 0 0 0 0 0 0 0 0 .................................................. Selected Device : 0s0 EDIT SENSE DATA BYTE HEX BINARY COMMENT 39 00 0 0 0 0 0 0 0 0 40 00 0 0 0 0 0 0 0 0 . 41 18 0 0 0 1 1 0 0 0 42 00 0 0 0 0 0 0 0 0 43 36 0 0 1 1 0 1 1 0 44 02 0 0 0 0 0 0 1 0 45 00 0 0 0 0 0 0 0 0 46 00 0 0 0 0 0 0 0 0 47 01 0 0 0 0 0 0 0 1 . 48 00 0 0 0 0 0 0 0 0 49 00 0 0 0 0 0 0 0 0 50 00 0 0 0 0 0 0 0 0 51 10 0 0 0 1 0 0 0 0 .................................................. Selected Device : 0s0 EDIT SENSE DATA BYTE HEX BINARY COMMENT 52 40 0 1 0 0 0 0 0 0 53 00 0 0 0 0 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB022 Pg003 54 00 0 0 0 0 0 0 0 0 . 55 00 0 0 0 0 0 0 0 0 56 04 0 0 0 0 0 1 0 0 Page 4 Start 57 12 0 0 0 1 0 0 1 0 Page Length : 18 bytes 58 00 0 0 0 0 0 0 0 0 59 06 0 0 0 0 0 1 1 0 . 60 60 0 1 1 0 0 0 0 0 61 08 0 0 0 0 1 0 0 0 62 00 0 0 0 0 0 0 0 0 63 00 0 0 0 0 0 0 0 0 64 00 0 0 0 0 0 0 0 0 ........................................................ Selected Device : 0s0 EDIT SENSE DATA BYTE HEX BINARY COMMENT 65 00 0 0 0 0 0 0 0 0 . 66 00 0 0 0 0 0 0 0 0 67 00 0 0 0 0 0 0 0 0 68 00 0 0 0 0 0 0 0 0 69 00 0 0 0 0 0 0 0 0 70 00 0 0 0 0 0 0 0 0 71 00 0 0 0 0 0 0 0 0 72 00 0 0 0 0 0 0 0 0 73 00 0 0 0 0 0 0 0 0 74 00 0 0 0 0 0 0 0 0 75 00 0 0 0 0 0 0 0 0 76 08 0 0 0 0 1 0 0 0 Page 8 Start 77 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes .................................................. Selected Device : 0s0 EDIT SENSE DATA BYTE HEX BINARY COMMENT 78 01 0 0 0 0 0 0 0 1 79 00 0 0 0 0 0 0 0 0 80 ff 1 1 1 1 1 1 1 1 81 ff 1 1 1 1 1 1 1 1 82 00 0 0 0 0 0 0 0 0 83 00 0 0 0 0 0 0 0 0 . 84 00 0 0 0 0 0 0 0 0 85 59 0 1 0 1 1 0 0 1 86 00 0 0 0 0 0 0 0 0 87 00 0 0 0 0 0 0 0 0 88 38 0 0 1 1 1 0 0 0 Page 38 Start 89 0e 0 0 0 0 1 1 1 0 Page Length : 14 bytes 90 01 0 0 0 0 0 0 0 1 .................................................. Selected Device : 0s0 EDIT SENSE DATA BYTE HEX BINARY COMMENT 91 ff 1 1 1 1 1 1 1 1 92 59 0 1 0 1 1 0 0 1 93 00 0 0 0 0 0 0 0 0 94 00 0 0 0 0 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB022 Pg004 . 95 00 0 0 0 0 0 0 0 0 96 00 0 0 0 0 0 0 0 0 97 00 0 0 0 0 0 0 0 0 98 00 0 0 0 0 0 0 0 0 . 99 00 0 0 0 0 0 0 0 0 100 00 0 0 0 0 0 0 0 0 101 00 0 0 0 0 0 0 0 0 102 00 0 0 0 0 0 0 0 0 103 00 0 0 0 0 0 0 0 0 ............................................................ Selected Device : 0s0 EDIT FORMAT PARAMETERS FORMAT-UNIT Command Block Bits FmtDat 1 CmpLst 0 Defect Header Parameters FOV 1 DPRY 0 DCRT 1 . STPF 1 DIVE Format Options Issue MODE SELECT Y Surface Analysis Y Use Edited G-List N ORIGINATOR: Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB022 Pg005 FIB 00023 MAI COMPANY CONFIDENTIAL 10/20/94 *** XT-8760S - GPx40 1.1C dive mode sense information *** The later levels of GPx40 dive display mode sense information in a different manner than the older levels, following is a series of dive screens from a Maxtor XT-8760S drive. DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== ERROR RECOVERY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Auto Write Reallocation Enabled Bit 0 0 0 0 Auto Read Reallocation Enabled Bit 0 0 0 0 Transfer Block Bit 1 0 1 1 Read Continuous Bit 0 0 0 1 Early Error Correction Bit 0 0 0 1 Post Error Bit 1 0 1 1 Disable Transfer on Error Bit 0 0 0 1 Disable Correction Bit 0 0 0 1 Correction Span 12 12 12 ff Head Offset Count 0 0 0 ff Retry.Count 16 16 16 ff Data Strobe Offset Count 0 0 0 0 Recover Limit 255 255 255 0 .................................................... DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DISCONNECT/RECONNECT CONTROL PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Buffer Full Ratio 0 0 0 ff Buffer Empty Ratio 0 0 0 ff Bus.Inactivity Limit 10 10 10 ffff Disconnect Time Limit 0 0 0 0 Connect Time Limit 0 0 0 0 .................................................................... DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DEVICE FORMAT PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Tracks per Zone 15 15 15 ffff Alternate Sectors per Zone 5 5 5 ffff Alternate Tracks per Zone 0 0 0 0 Alternate Tracks per Volume 45 45 45 ffff Sectors per Track 54 54 54 ffff Data Bytes per Physical Sector 512 512 512 ffff Interleave 1 1 1 0 Track Skew 0 0 0 ffff Cylinder.Skew 8 65535 8 ffff Soft Sector Format Bit 0 0 0 0 Hard Sector Format Bit 1 1 1 0 Removeable Media Bit 0 0 0 0 Surface Bit 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB023 Pg001 .............................................................................. DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DRIVE GEOMETRY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Maximum Number of Cylinders 1632 1632 1632 ffffff Maximum Number of Heads 15 15 15 ff Start Cyl - Write Precompensation 0 0 0 0 Start Cyl - Reduced Write Current 0 0 0 0 Drive Step Rate 0 0 0 0 Landing Zone Cylinder 0 0 0 0 .................................................................. DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== CACHE PAGE PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Write Cache Enable Bit 0 0 0 0 Multiplication Factor 0 0 0 0 Read Cache Disable 1 1 1 1 Demand Read Retension Priority 0 0 0 0 Write Retension Priority 0 0 0 0 Disable Pre-fetch Transfer Length 65535 65535 65535 0 Minimum Pre-fetch 0 0 0 0 Maximum Pre-fetch 89 89 89 0 Maximum Pre-fetch Ceiling 0 0 0 0 ............................................................ DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT FORMAT PARAMETERS FORMAT-UNIT Command Block Bits FmtDat 1 CmpLst 0 Defect Header Parameters FOV 1 DPRY 0 DCRT 1 . STPF 1 DIVE Format Options Issue MODE SELECT Y Surface Analysis Y Use Edited G-List N ...................................................................... DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 0 00 0 0 0 0 0 0 0 0 Parameter List Header 1 00 0 0 0 0 0 0 0 0 2 00 0 0 0 0 0 0 0 0 . 3 08 0 0 0 0 1 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB023 Pg002 4 00 0 0 0 0 0 0 0 0 Block Descriptor 5 00 0 0 0 0 0 0 0 0 6 00 0 0 0 0 0 0 0 0 7 00 0 0 0 0 0 0 0 0 . 8 00 0 0 0 0 0 0 0 0 9 00 0 0 0 0 0 0 0 0 10 02 0 0 0 0 0 0 1 0 . 11 00 0 0 0 0 0 0 0 0 12 01 0 0 0 0 0 0 0 1 Page 1 Start ............................................................ DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 13 06 0 0 0 0 0 1 1 0 Page Length : 6 bytes 14 24 0 0 1 0 0 1 0 0 15 10 0 0 0 1 0 0 0 0 16 0c 0 0 0 0 1 1 0 0 17 00 0 0 0 0 0 0 0 0 18 00 0 0 0 0 0 0 0 0 19 ff 1 1 1 1 1 1 1 1 20 02 0 0 0 0 0 0 1 0 Page 2 Start 21 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes . 22 00 0 0 0 0 0 0 0 0 23 00 0 0 0 0 0 0 0 0 24 00 0 0 0 0 0 0 0 0 25 0a 0 0 0 0 1 0 1 0 .................................................. DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 26 00 0 0 0 0 0 0 0 0 27 00 0 0 0 0 0 0 0 0 28 00 0 0 0 0 0 0 0 0 29 00 0 0 0 0 0 0 0 0 30 00 0 0 0 0 0 0 0 0 31 00 0 0 0 0 0 0 0 0 32 03 0 0 0 0 0 0 1 1 Page 3 Start 33 16 0 0 0 1 0 1 1 0 Page Length : 22 bytes 34 00 0 0 0 0 0 0 0 0 35 0f 0 0 0 0 1 1 1 1 36 00 0 0 0 0 0 0 0 0 37 05 0 0 0 0 0 1 0 1 38 00 0 0 0 0 0 0 0 0 .................................................. DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 39 00 0 0 0 0 0 0 0 0 40 00 0 0 0 0 0 0 0 0 41 2d 0 0 1 0 1 1 0 1 42 00 0 0 0 0 0 0 0 0 43 36 0 0 1 1 0 1 1 0 44 02 0 0 0 0 0 0 1 0 DISK I/O-MAXTOR-ALL---------------------------------FIB023 Pg003 45 00 0 0 0 0 0 0 0 0 46 00 0 0 0 0 0 0 0 0 47 01 0 0 0 0 0 0 0 1 . 48 00 0 0 0 0 0 0 0 0 49 00 0 0 0 0 0 0 0 0 50 00 0 0 0 0 0 0 0 0 51 08 0 0 0 0 1 0 0 0 ................................................................ DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 52 40 0 1 0 0 0 0 0 0 53 00 0 0 0 0 0 0 0 0 54 00 0 0 0 0 0 0 0 0 . 55 00 0 0 0 0 0 0 0 0 56 04 0 0 0 0 0 1 0 0 Page 4 Start 57 12 0 0 0 1 0 0 1 0 Page Length : 18 bytes 58 00 0 0 0 0 0 0 0 0 59 06 0 0 0 0 0 1 1 0 . 60 60 0 1 1 0 0 0 0 0 61 0f 0 0 0 0 1 1 1 1 62 00 0 0 0 0 0 0 0 0 63 00 0 0 0 0 0 0 0 0 64 00 0 0 0 0 0 0 0 0 .................................................. DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 65 00 0 0 0 0 0 0 0 0 . 66 00 0 0 0 0 0 0 0 0 67 00 0 0 0 0 0 0 0 0 68 00 0 0 0 0 0 0 0 0 69 00 0 0 0 0 0 0 0 0 70 00 0 0 0 0 0 0 0 0 71 00 0 0 0 0 0 0 0 0 72 00 0 0 0 0 0 0 0 0 73 00 0 0 0 0 0 0 0 0 74 00 0 0 0 0 0 0 0 0 75 00 0 0 0 0 0 0 0 0 76 08 0 0 0 0 1 0 0 0 Page 8 Start 77 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes .................................................. DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 78 01 0 0 0 0 0 0 0 1 79 00 0 0 0 0 0 0 0 0 80 ff 1 1 1 1 1 1 1 1 81 ff 1 1 1 1 1 1 1 1 82 00 0 0 0 0 0 0 0 0 83 00 0 0 0 0 0 0 0 0 . 84 00 0 0 0 0 0 0 0 0 85 59 0 1 0 1 1 0 0 1 DISK I/O-MAXTOR-ALL---------------------------------FIB023 Pg004 86 00 0 0 0 0 0 0 0 0 87 00 0 0 0 0 0 0 0 0 88 38 0 0 1 1 1 0 0 0 Page 38 Start 89 0e 0 0 0 0 1 1 1 0 Page Length : 14 bytes 90 01 0 0 0 0 0 0 0 1 .................................................................... DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 91 ff 1 1 1 1 1 1 1 1 92 59 0 1 0 1 1 0 0 1 93 00 0 0 0 0 0 0 0 0 94 00 0 0 0 0 0 0 0 0 . 95 00 0 0 0 0 0 0 0 0 96 00 0 0 0 0 0 0 0 0 97 00 0 0 0 0 0 0 0 0 98 00 0 0 0 0 0 0 0 0 . 99 00 0 0 0 0 0 0 0 0 100 00 0 0 0 0 0 0 0 0 101 00 0 0 0 0 0 0 0 0 102 00 0 0 0 0 0 0 0 0 103 00 0 0 0 0 0 0 0 0 ORIGINATOR: Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB023 Pg005 FIB 00024 MAI COMPANY CONFIDENTIAL 11/19/94 *** LXT-535S - GPx40 DIVE mode sense information *** The later levels of dive display mode sense information in a different manner than previous levels, following are the correct mode sense parameters for a LXT-535S drive. MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== INQUIRY AND CAPACITY DATA --------------------------------INQUIRY DATA----------------------------------- Peripheral Device Type = 0 Device Type Qualifier = 0 ANSI Version = 1 Response Data Format = 1 Vendor ID = MAXTOR Product ID = LXT-535S Firmware Revision Level = 8.57 --------------------------------CAPACITY DATA---------------------------------- Highest Logical Block Address = 1045241 Block Length = 512 ------------------------------------------------------------------------------- MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== ERROR RECOVERY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Auto Write Reallocation Enabled Bit 0 0 0 1 Auto Read Reallocation Enabled Bit 0 0 0 1 Transfer Block Bit 0 0 0 1 Read Continuous Bit 0 0 0 1 Early Error Correction Bit 0 0 0 1 Post Error Bit 0 0 0 1 Disable Transfer on Error Bit 0 0 0 1 Disable Correction Bit 0 0 0 1 Correction Span 11 11 11 f Head Offset Count 0 0 0 0 Retry Count 8 8 8 ff Data Strobe Offset Count 0 0 0 0 Recover Limit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DISCONNECT/RECONNECT CONTROL PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Buffer Full Ratio 16 16 16 ff Buffer Empty Ratio 64 64 64 ff Bus Inactivity Limit 0 0 0 0 Disconnect Time Limit 0 0 0 0 Connect Time Limit 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB024 Pg001 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DEVICE FORMAT PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Tracks per Zone 1 1 1 0 Alternate Sectors per Zone 1 1 1 ffff Alternate Tracks per Zone 0 0 0 0 Alternate Tracks per Volume 7 7 7 0 Sectors per Track 42 42 42 0 Data Bytes per Physical Sector 512 512 512 ffff Interleave 1 1 1 0 Track Skew 1 1 1 0 Cylinder Skew 21 21 21 0 Soft Sector Format Bit 0 0 0 0 Hard Sector Format Bit 1 1 1 0 Removeable Media Bit 0 0 0 0 Surface Bit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DRIVE GEOMETRY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Maximum Number of Cylinders 1546 1546 1546 ffff Maximum Number of Heads 11 11 11 ff Start Cyl - Write Precompensation 0 0 0 0 Start Cyl - Reduced Write Current 0 0 0 0 Drive Step Rate 0 0 0 0 Landing Zone Cylinder 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== CACHE PAGE PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Write Cache Enable Bit 0 0 0 1 Multiplication Factor 0 0 0 0 Read Cache Disable 0 0 0 1 Demand Read Retension Priority 1 1 1 f Write Retension Priority 1 1 1 f Disable Pre-fetch Transfer Length 65471 65471 65471 ffff Minimum Pre-fetch 0 0 0 ffff Maximum Pre-fetch 64 64 64 ffff Maximum Pre-fetch Ceiling 64 64 64 ffff MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 0 00 0 0 0 0 0 0 0 0 Parameter List Header 1 00 0 0 0 0 0 0 0 0 2 00 0 0 0 0 0 0 0 0 . 3 08 0 0 0 0 1 0 0 0 4 00 0 0 0 0 0 0 0 0 Block Descriptor 5 0f 0 0 0 0 1 1 1 1 6 f2 1 1 1 1 0 0 1 0 7 f9 1 1 1 1 1 0 0 1 . 8 00 0 0 0 0 0 0 0 0 9 00 0 0 0 0 0 0 0 0 10 02 0 0 0 0 0 0 1 0 DISK I/O-MAXTOR-ALL---------------------------------FIB024 Pg002 . 11 00 0 0 0 0 0 0 0 0 12 01 0 0 0 0 0 0 0 1 Page 1 Start 13 06 0 0 0 0 0 1 1 0 Page Length : 6 bytes 14 00 0 0 0 0 0 0 0 0 15 08 0 0 0 0 1 0 0 0 16 0b 0 0 0 0 1 0 1 1 17 00 0 0 0 0 0 0 0 0 18 00 0 0 0 0 0 0 0 0 19 00 0 0 0 0 0 0 0 0 20 02 0 0 0 0 0 0 1 0 Page 2 Start 21 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes . 22 10 0 0 0 1 0 0 0 0 23 40 0 1 0 0 0 0 0 0 24 00 0 0 0 0 0 0 0 0 25 00 0 0 0 0 0 0 0 0 26 00 0 0 0 0 0 0 0 0 27 00 0 0 0 0 0 0 0 0 28 00 0 0 0 0 0 0 0 0 29 00 0 0 0 0 0 0 0 0 30 00 0 0 0 0 0 0 0 0 31 00 0 0 0 0 0 0 0 0 32 03 0 0 0 0 0 0 1 1 Page 3 Start 33 16 0 0 0 1 0 1 1 0 Page Length : 22 bytes 34 00 0 0 0 0 0 0 0 0 35 01 0 0 0 0 0 0 0 1 36 00 0 0 0 0 0 0 0 0 37 01 0 0 0 0 0 0 0 1 38 00 0 0 0 0 0 0 0 0 39 00 0 0 0 0 0 0 0 0 40 00 0 0 0 0 0 0 0 0 41 07 0 0 0 0 0 1 1 1 42 00 0 0 0 0 0 0 0 0 43 2a 0 0 1 0 1 0 1 0 44 02 0 0 0 0 0 0 1 0 45 00 0 0 0 0 0 0 0 0 46 00 0 0 0 0 0 0 0 0 47 01 0 0 0 0 0 0 0 1 . 48 00 0 0 0 0 0 0 0 0 49 01 0 0 0 0 0 0 0 1 50 00 0 0 0 0 0 0 0 0 51 15 0 0 0 1 0 1 0 1 52 40 0 1 0 0 0 0 0 0 53 00 0 0 0 0 0 0 0 0 54 00 0 0 0 0 0 0 0 0 . 55 00 0 0 0 0 0 0 0 0 56 04 0 0 0 0 0 1 0 0 Page 4 Start 57 16 0 0 0 1 0 1 1 0 Page Length : 22 bytes 58 00 0 0 0 0 0 0 0 0 59 06 0 0 0 0 0 1 1 0 60 0a 0 0 0 0 1 0 1 0 61 0b 0 0 0 0 1 0 1 1 62 00 0 0 0 0 0 0 0 0 63 00 0 0 0 0 0 0 0 0 64 00 0 0 0 0 0 0 0 0 65 00 0 0 0 0 0 0 0 0 . 66 00 0 0 0 0 0 0 0 0 67 00 0 0 0 0 0 0 0 0 68 00 0 0 0 0 0 0 0 0 69 00 0 0 0 0 0 0 0 0 70 00 0 0 0 0 0 0 0 0 71 00 0 0 0 0 0 0 0 0 72 00 0 0 0 0 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB024 Pg003 73 00 0 0 0 0 0 0 0 0 74 00 0 0 0 0 0 0 0 0 75 00 0 0 0 0 0 0 0 0 76 0e 0 0 0 0 1 1 1 0 . 77 10 0 0 0 1 0 0 0 0 78 00 0 0 0 0 0 0 0 0 79 00 0 0 0 0 0 0 0 0 80 08 0 0 0 0 1 0 0 0 Page 8 Start 81 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes 82 00 0 0 0 0 0 0 0 0 83 11 0 0 0 1 0 0 0 1 . 84 ff 1 1 1 1 1 1 1 1 85 bf 1 0 1 1 1 1 1 1 86 00 0 0 0 0 0 0 0 0 87 00 0 0 0 0 0 0 0 0 . 88 00 0 0 0 0 0 0 0 0 89 40 0 1 0 0 0 0 0 0 90 00 0 0 0 0 0 0 0 0 91 40 0 1 0 0 0 0 0 0 Enter the number of the byte to modify >>> f - Scroll forward 1 line b - Scroll backward 1 line F - Page forward B - Page backward ESC to Quit ORIGINATOR: Ira Leibowitz/Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB024 Pg004 FIB 00025 MAI COMPANY CONFIDENTIAL 11/19/94 *** XT-3280 - GPx40 dive mode sense information *** The later levels of dive display mode sense information in a different manner than previous levels, following are dive screens from a XT3280 drive. MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== INQUIRY AND CAPACITY DATA --------------------------------INQUIRY DATA----------------------------------- Peripheral Device Type = 0 Device Type Qualifier = 0 ANSI Version = 0 Response Data Format = 1 Vendor ID = MBF-DISK Product ID = XT-3280 Firmware.Revision Level = B402 --------------------------------CAPACITY DATA---------------------------------- Highest Logical Block Address = 254425 Block Length = 1024 ------------------------------------------------------------------------------- MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DISPLAY MODE SENSE DATA MENU 1 PAGE 1 - Error Recovery Parameters 2 PAGE 2 - Disconnect/Reconnect Control Parameters 3 PAGE 3 - Device Format Parameters 4 PAGE 4 - Drive Geometry Parameters 5 PAGE 8 - Cache Page Parameters 6 PAGE n - Display Miscellaneous Page WARNING: Invalid page length field (0x 2) detected on page 1 Press to continue. MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== ERROR RECOVERY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Auto Write Reallocation Enabled Bit 0 0 0 0 Auto Read Reallocation Enabled Bit 0 0 0 0 Transfer Block Bit 0 0 0 0 Read Continuous Bit 0 0 0 0 Early Error Correction Bit 0 0 0 0 Post Error Bit 0 0 0 0 Disable Transfer on Error Bit 0 0 0 0 Disable Correction Bit 0 0 0 0 Correction.Span 0 0 0 0 Head Offset Count 0 0 0 0 Retry Count 0 0 0 0 Data Strobe Offset Count 0 0 0 0 Recover Limit 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB025 Pg001 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DISPLAY MODE SENSE DATA MENU 1 PAGE 1 - Error Recovery Parameters 2 PAGE 2 - Disconnect/Reconnect Control Parameters 3 PAGE 3 - Device Format Parameters 4 PAGE 4 - Drive Geometry Parameters 5 PAGE 8 - Cache Page Parameters 6 PAGE n - Display Miscellaneous Page ERROR encountered issuing MODE SENSE command! A sense key of hex 5 and a sense code of hex 24 have been detected. Press to continue. MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DISCONNECT/RECONNECT CONTROL PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Buffer Full Ratio 0 0 0 0 Buffer Empty Ratio 0 0 0 0 Bus Inactivity Limit 0 0 0 0 Disconnect Time Limit 0 0 0 0 Connect Time Limit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DEVICE FORMAT PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Tracks per Zone 15 15 15 ffff Alternate Sectors per Zone 2 2 2 ffff Alternate Tracks per Zone 0 0 0 0 Alternate Tracks per Volume 2 2 2 0 Sectors per Track 14 26 14 ffff Data Bytes per Physical Sector 1024 512 1024 ffff Interleave 1 1 1 0 Track Skew 0 0 0 0 Cylinder Skew 0 0 0 0 Soft Sector Format Bit 1 1 1 0 Hard Sector Format Bit 0 0 0 0 Removeable Media Bit 0 0 0 0 Surface Bit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DRIVE GEOMETRY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Maximum Number of Cylinders 1224 1224 1224 ffffff Maximum Number of Heads 15 15 15 ff Start Cyl - Write Precompensation 0 0 0 0 Start Cyl - Reduced Write Current 0 0 0 0 Drive Step Rate 92 92 92 0 Landing Zone Cylinder 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB025 Pg002 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== CACHE PAGE PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Write Cache Enable Bit 0 0 0 0 Multiplication Factor 0 0 0 0 Read Cache Disable 0 0 0 0 Demand Read Retension Priority 0 0 0 0 Write Retension Priority 0 0 0 0 Disable Pre-fetch Transfer Length 0 0 0 0 Minimum Pre-fetch 0 0 0 0 Maximum Pre-fetch 0 0 0 0 Maximum Pre-fetch Ceiling 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== . MAIN MENU 1 Device Selection 2 Format 3 Surface Analysis 4 Verify 5 Inspect 6 Reboot WARNING: Invalid page length field (0x 2) detected on page 1 Press to continue. MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 0 00 0 0 0 0 0 0 0 0 Parameter List Header 1 00 0 0 0 0 0 0 0 0 2 00 0 0 0 0 0 0 0 0 . 3 08 0 0 0 0 1 0 0 0 4 00 0 0 0 0 0 0 0 0 Block Descriptor 5 00 0 0 0 0 0 0 0 0 6 00 0 0 0 0 0 0 0 0 7 00 0 0 0 0 0 0 0 0 . 8 00 0 0 0 0 0 0 0 0 9 00 0 0 0 0 0 0 0 0 10 04 0 0 0 0 0 1 0 0 . 11 00 0 0 0 0 0 0 0 0 12 01 0 0 0 0 0 0 0 1 Page 1 Start 13 02 0 0 0 0 0 0 1 0 Page Length : 2 bytes 14 25 0 0 1 0 0 1 0 1 15 00 0 0 0 0 0 0 0 0 16 03 0 0 0 0 0 0 1 1 Page 3 Start 17 16 0 0 0 1 0 1 1 0 Page Length : 22 bytes 18 00 0 0 0 0 0 0 0 0 19 0f 0 0 0 0 1 1 1 1 20 00 0 0 0 0 0 0 0 0 . 21 02 0 0 0 0 0 0 1 0 . 22 00 0 0 0 0 0 0 0 0 23 00 0 0 0 0 0 0 0 0 24 00 0 0 0 0 0 0 0 0 25 02 0 0 0 0 0 0 1 0 26 00 0 0 0 0 0 0 0 0 27 0e 0 0 0 0 1 1 1 0 DISK I/O-MAXTOR-ALL---------------------------------FIB025 Pg003 28 04 0 0 0 0 0 1 0 0 29 00 0 0 0 0 0 0 0 0 30 00 0 0 0 0 0 0 0 0 31 01 0 0 0 0 0 0 0 1 32 00 0 0 0 0 0 0 0 0 . 33 00 0 0 0 0 0 0 0 0 34 00 0 0 0 0 0 0 0 0 35 00 0 0 0 0 0 0 0 0 . 36 80 1 0 0 0 0 0 0 0 37 00 0 0 0 0 0 0 0 0 38 00 0 0 0 0 0 0 0 0 39 00 0 0 0 0 0 0 0 0 40 04 0 0 0 0 0 1 0 0 Page 4 Start 41 12 0 0 0 1 0 0 1 0 Page Length : 18 bytes 42 00 0 0 0 0 0 0 0 0 43 04 0 0 0 0 0 1 0 0 44 c8 1 1 0 0 1 0 0 0 45 0f 0 0 0 0 1 1 1 1 46 00 0 0 0 0 0 0 0 0 47 00 0 0 0 0 0 0 0 0 . 48 00 0 0 0 0 0 0 0 0 49 00 0 0 0 0 0 0 0 0 50 00 0 0 0 0 0 0 0 0 51 00 0 0 0 0 0 0 0 0 52 00 0 0 0 0 0 0 0 0 53 5c 0 1 0 1 1 1 0 0 54 00 0 0 0 0 0 0 0 0 . 55 00 0 0 0 0 0 0 0 0 56 00 0 0 0 0 0 0 0 0 57 00 0 0 0 0 0 0 0 0 58 00 0 0 0 0 0 0 0 0 . 59 00 0 0 0 0 0 0 0 0 Enter the number of the byte to modify >>> f - Scroll forward 1 line b - Scroll backward 1 line F - Page forward B - Page backward ESC to Quit ORIGINATOR: Ira Leibowitz/Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB025 Pg004 FIB 00026 MAI COMPANY CONFIDENTIAL 11/19/94 *** 7213SR - GPx40 dive mode sense information *** The later levels of dive display mode sense information in a different manner than previous levels, following are dive screens from a 7213SR drive. MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== INQUIRY AND CAPACITY DATA --------------------------------INQUIRY DATA----------------------------------- Peripheral Device Type = 0 Device Type Qualifier = 0 ANSI Version = 1 Response Data Format = 1 Vendor ID = MAXTOR Product ID = 7213-SCSI Firmware Revision Level = 1157 --------------------------------CAPACITY DATA---------------------------------- Highest Logical Block Address = 415599 Block Length = 512 ------------------------------------------------------------------------------- MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== ERROR RECOVERY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Auto Write Reallocation Enabled Bit 0 0 0 1 Auto Read Reallocation Enabled Bit 0 0 0 1 Transfer Block Bit 1 0 1 1 Read Continuous Bit 0 0 0 1 Early Error Correction Bit 0 0 0 1 Post Error Bit 1 0 1 1 Disable Transfer on Error Bit 0 0 0 1 Disable Correction Bit 0 0 0 1 Correction Span 11 11 11 0 Head Offset Count 0 0 0 0 Retry.Count 8 16 8 ff Data Strobe Offset Count 0 0 0 0 Recover Limit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DISCONNECT/RECONNECT CONTROL PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Buffer Full Ratio 160 160 160 ff Buffer Empty Ratio 192 192 192 ff Bus Inactivity Limit 0 0 0 0 Disconnect Time Limit 2 2 2 0 Connect Time Limit 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB026 Pg001 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DEVICE FORMAT PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Tracks per Zone 4 4 4 0 Alternate Sectors per Zone 4 4 4 0 Alternate Tracks per Zone 0 0 0 0 Alternate Tracks per Volume 4 4 4 0 Sectors per Track 72 72 72 0 Data Bytes per Physical Sector 512 512 512 0 Interleave 1 1 1 0 Track Skew 18 18 18 0 Cylinder Skew 26 26 26 0 Soft Sector Format Bit 0 0 0 0 Hard Sector Format Bit 1 1 1 0 Removeable Media Bit 0 0 0 0 Surface Bit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== DRIVE GEOMETRY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Maximum Number of Cylinders 1690 1690 1690 0 Maximum Number of Heads 4 4 4 0 Start Cyl - Write Precompensation 0 0 0 0 Start Cyl - Reduced Write Current 0 0 0 0 Drive Step Rate 0 0 0 0 Landing Zone Cylinder 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== CACHE PAGE PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Write Cache Enable Bit 0 0 0 0 Multiplication Factor 0 0 0 0 Read Cache Disable 0 0 0 1 Demand Read Retension Priority 0 0 0 0 Write Retension Priority 0 0 0 0 Disable Pre-fetch Transfer Length 0 0 0 0 Minimum Pre-fetch 0 0 0 0 Maximum Pre-fetch 124 124 124 0 Maximum.Pre-fetch Ceiling 124 124 124 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 2.1A*03 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 0 00 0 0 0 0 0 0 0 0 Parameter List Header 1 00 0 0 0 0 0 0 0 0 2 00 0 0 0 0 0 0 0 0 . 3 08 0 0 0 0 1 0 0 0 4 00 0 0 0 0 0 0 0 0 Block Descriptor 5 06 0 0 0 0 0 1 1 0 6 57 0 1 0 1 0 1 1 1 7 70 0 1 1 1 0 0 0 0 . 8 00 0 0 0 0 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB026 Pg002 9 00 0 0 0 0 0 0 0 0 10 02 0 0 0 0 0 0 1 0 . 11 00 0 0 0 0 0 0 0 0 12 01 0 0 0 0 0 0 0 1 Page 1 Start 13 06 0 0 0 0 0 1 1 0 Page Length : 6 bytes 14 24 0 0 1 0 0 1 0 0 15 08 0 0 0 0 1 0 0 0 16 0b 0 0 0 0 1 0 1 1 17 00 0 0 0 0 0 0 0 0 18 00 0 0 0 0 0 0 0 0 19 00 0 0 0 0 0 0 0 0 20 02 0 0 0 0 0 0 1 0 Page 2 Start 21 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes 22 a0 1 0 1 0 0 0 0 0 23 c0 1 1 0 0 0 0 0 0 24 00 0 0 0 0 0 0 0 0 25 00 0 0 0 0 0 0 0 0 26 00 0 0 0 0 0 0 0 0 27 02 0 0 0 0 0 0 1 0 28 00 0 0 0 0 0 0 0 0 29 00 0 0 0 0 0 0 0 0 30 00 0 0 0 0 0 0 0 0 31 00 0 0 0 0 0 0 0 0 32 03 0 0 0 0 0 0 1 1 Page 3 Start 33 16 0 0 0 1 0 1 1 0 Page Length : 22 bytes 34 00 0 0 0 0 0 0 0 0 35 04 0 0 0 0 0 1 0 0 36 00 0 0 0 0 0 0 0 0 37 04 0 0 0 0 0 1 0 0 38 00 0 0 0 0 0 0 0 0 39 00 0 0 0 0 0 0 0 0 40 00 0 0 0 0 0 0 0 0 . 41 04 0 0 0 0 0 1 0 0 42 00 0 0 0 0 0 0 0 0 43 48 0 1 0 0 1 0 0 0 44 02 0 0 0 0 0 0 1 0 45 00 0 0 0 0 0 0 0 0 46 00 0 0 0 0 0 0 0 0 47 01 0 0 0 0 0 0 0 1 . 48 00 0 0 0 0 0 0 0 0 49 12 0 0 0 1 0 0 1 0 50 00 0 0 0 0 0 0 0 0 51 1a 0 0 0 1 1 0 1 0 52 40 0 1 0 0 0 0 0 0 53 00 0 0 0 0 0 0 0 0 54 00 0 0 0 0 0 0 0 0 . 55 00 0 0 0 0 0 0 0 0 56 04 0 0 0 0 0 1 0 0 Page 4 Start 57 12 0 0 0 1 0 0 1 0 Page Length : 18 bytes 58 00 0 0 0 0 0 0 0 0 59 06 0 0 0 0 0 1 1 0 60 9a 1 0 0 1 1 0 1 0 61 04 0 0 0 0 0 1 0 0 62 00 0 0 0 0 0 0 0 0 63 00 0 0 0 0 0 0 0 0 64 00 0 0 0 0 0 0 0 0 65 00 0 0 0 0 0 0 0 0 . 66 00 0 0 0 0 0 0 0 0 67 00 0 0 0 0 0 0 0 0 68 00 0 0 0 0 0 0 0 0 69 00 0 0 0 0 0 0 0 0 70 00 0 0 0 0 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB026 Pg003 71 00 0 0 0 0 0 0 0 0 72 00 0 0 0 0 0 0 0 0 73 00 0 0 0 0 0 0 0 0 74 00 0 0 0 0 0 0 0 0 75 00 0 0 0 0 0 0 0 0 76 08 0 0 0 0 1 0 0 0 Page 8 Start 77 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes 78 00 0 0 0 0 0 0 0 0 79 00 0 0 0 0 0 0 0 0 80 00 0 0 0 0 0 0 0 0 81 00 0 0 0 0 0 0 0 0 82 00 0 0 0 0 0 0 0 0 83 00 0 0 0 0 0 0 0 0 . 84 00 0 0 0 0 0 0 0 0 85 7c 0 1 1 1 1 1 0 0 86 00 0 0 0 0 0 0 0 0 87 7c 0 1 1 1 1 1 0 0 88 20 0 0 1 0 0 0 0 0 Page 20 Start 89 0e 0 0 0 0 1 1 1 0 Page Length : 14 bytes 90 20 0 0 1 0 0 0 0 0 91 20 0 0 1 0 0 0 0 0 92 20 0 0 1 0 0 0 0 0 93 20 0 0 1 0 0 0 0 0 94 20 0 0 1 0 0 0 0 0 95 20 0 0 1 0 0 0 0 0 96 42 0 1 0 0 0 0 1 0 97 31 0 0 1 1 0 0 0 1 98 30 0 0 1 1 0 0 0 0 99 53 0 1 0 1 0 0 1 1 100 42 0 1 0 0 0 0 1 0 101 5a 0 1 0 1 1 0 1 0 102 57 0 1 0 1 0 1 1 1 103 53 0 1 0 1 0 0 1 1 104 00 0 0 0 0 0 0 0 0 Page 0 Start 105 02 0 0 0 0 0 0 1 0 Page Length : 2 bytes 106 10 0 0 0 1 0 0 0 0 107 00 0 0 0 0 0 0 0 0 Enter the number of the byte to modify >>> f - Scroll forward 1 line b - Scroll backward 1 line F - Page forward B - Page backward ESC to Quit ORIGINATOR: Ira Leibowitz/Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB026 Pg004 FIB 00027 MAI COMPANY CONFIDENTIAL 01/19/95 *** GPx40 mode sense information for the P1-17S 1.6GB drive *** NOTE: When changing parameters (i.e. from 1024 bytes per physical sector to 512) check the changeable field from the INSPECT option, if the field is 0 (i.e. sectors per track) DO NOT ATTEMPT TO CHANGE. If a non-changeable field is modified, the FORMAT will complete (about an hour later) but the desired changes will not take effect! When the bytes per physical block are changed and the drive formatted, the sectors per track will be automatically adjusted. Following are screens from GPx40 1.1C dive for a P1-17S drive. MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== . MAIN MENU 1 Select a Device 2 Format 3 Surface Analysis 4 Verify 5 Inspect 6 Reboot MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : NONE =============================================================================== DEVICE SELECTION Number of disk devices : 1 Drive Board Unit Device Description 0 0 0 0s0 SCSI, P1-17S MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== INSPECT MENU 1 Display Mode Sense Parameters 2 Display Inquiry and Capacity Data 3 Display Defect Data 4 Display Disk Data MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== INQUIRY AND CAPACITY DATA --------------------------------INQUIRY DATA----------------------------------- Peripheral Device Type = 0 Device Type Qualifier = 0 ANSI Version = 1 Response Data Format = 42 Vendor ID = MAXTOR Product ID = P1-17S Firmware Revision Level = LB22 --------------------------------CAPACITY DATA---------------------------------- Highest Logical Block Address = 2936592 Block Length = 512 ------------------------------------------------------------------------------- DISK I/O-MAXTOR-ALL---------------------------------FIB027 Pg001 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DISPLAY MODE SENSE DATA MENU 1 PAGE 1 - Error Recovery Parameters 2 PAGE 2 - Disconnect/Reconnect Control Parameters 3 PAGE 3 - Device Format Parameters 4 PAGE 4 - Drive Geometry Parameters 5 PAGE 8 - Cache Page Parameters 6 PAGE n - Display Miscellaneous Page MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== ERROR RECOVERY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Auto Write Reallocation Enabled Bit 0 0 0 1 Auto Read Reallocation Enabled Bit 0 0 0 1 Transfer Block Bit 1 0 1 1 Read Continuous Bit 0 0 0 1 Early Error Correction Bit 0 0 0 1 Post Error Bit 1 0 1 1 Disable Transfer on Error Bit 0 0 0 1 Disable Correction Bit 0 0 0 1 Correction.Span 22 22 22 ff Head Offset Count 6 6 6 ff Retry Count 14 14 14 ff Data Strobe Offset Count 2 2 2 ff Recover Limit 0 0 0 ff MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DISCONNECT/RECONNECT CONTROL PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Buffer Full Ratio 1 1 1 ff Buffer Empty Ratio 64 64 64 ff Bus Inactivity Limit 0 0 0 0 Disconnect Time Limit 0 0 0 0 Connect Time Limit 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DEVICE FORMAT PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Tracks per Zone 19 19 19 0 Alternate Sectors per Zone 6 6 6 ff Alternate Tracks per Zone 0 0 0 0 Alternate Tracks per Volume 0 0 0 0 Sectors per Track 101 101 101 0 Data Bytes per Physical Sector 512 512 512 ffff Interleave 1 1 1 ff Track Skew 0 0 0 0 Cylinder Skew 12 12 12 ff Soft Sector Format Bit 0 0 0 0 Hard Sector Format Bit 1 1 1 0 Removeable Media Bit 0 0 0 0 Surface Bit 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB027 Pg002 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== DRIVE GEOMETRY PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Maximum Number of Cylinders 1778 1778 1778 ffff . Maximum Number of Heads 19 19 19 ff Start Cyl - Write Precompensation 0 0 0 0 Start Cyl - Reduced Write Current 0 0 0 0 Drive Step Rate 0 0 0 0 Landing Zone Cylinder 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== CACHE PAGE PARAMETERS SENSE DATA FIELD CURRENT DEFAULT SAVED CHANGEABLE Write Cache Enable Bit 0 0 0 1 Multiplication Factor 0 0 0 1 Read Cache Disable 0 0 0 1 Demand Read Retension Priority 0 0 0 0 Write Retension Priority 0 0 0 0 Disable Pre-fetch Transfer Length 0 0 0 0 Minimum Pre-fetch 0 0 0 0 Maximum Pre-fetch 0 0 0 0 Maximum Pre-fetch Ceiling 0 0 0 0 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== SENSE PAGE HEX DUMP PAGE : 01 PARAMETER LIST HEADER : 17 00 00 08 PARAMETER LIST BLOCK DESCRIPTER : 00 2c cf 11 00 00 02 00 OFFSET CURRENT DEFAULT SAVED CHANGEABLE 0 81 0a 24 0e 81 0a 00 0e 81 0a 24 0e 81 0a ff ff 4 16 06 02 00 16 06 02 00 16 06 02 00 ff ff ff 00 8 00 00 00 00 04 00 00 00 00 00 00 00 ff 00 00 ff PAGE : 02 PARAMETER LIST HEADER : 1b 00 00 08 PARAMETER LIST BLOCK DESCRIPTER : 00 2c cf 11 00 00 02 00 OFFSET CURRENT DEFAULT SAVED CHANGEABLE 0 82 0e 01 40 82 0e 01 40 82 0e 01 40 82 0e ff ff 4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . 8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 PAGE : 03 PARAMETER LIST HEADER : 23 00 00 08 PARAMETER LIST BLOCK DESCRIPTER : 00 2c cf 11 00 00 02 00 OFFSET CURRENT DEFAULT SAVED CHANGEABLE . 0 83 16 00 13 03 16 00 13 03 16 00 13 03 16 00 00 4 00 06 00 00 00 06 00 00 00 06 00 00 00 ff 00 00 8 00 00 00 65 00 00 00 65 00 00 00 65 00 00 00 00 . 12 02 00 00 01 02 00 00 01 02 00 00 01 ff ff 00 ff 16 00 00 00 0c 00 00 00 0c 00 00 00 0c 00 00 00 ff 20 40 00 00 00 40 00 00 00 40 00 00 00 00 00 00 00 DISK I/O-MAXTOR-ALL---------------------------------FIB027 Pg003 PAGE : 04 PARAMETER LIST HEADER : 23 00 00 08 PARAMETER LIST BLOCK DESCRIPTER : 00 2c cf 11 00 00 02 00 OFFSET CURRENT DEFAULT SAVED CHANGEABLE 0 84 16 00 06 84 16 00 06 84 16 00 06 84 16 00 ff 4 f2 13 00 00 f2 13 00 00 f2 13 00 00 ff ff 00 00 . 8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 16 00 00 00 00 00 00 00 00 00 00 00 00 00 ff ff 00 20 0e 10 00 00 0e 10 00 00 0e 10 00 00 00 00 00 00 PAGE : 08 PARAMETER LIST HEADER : 17 00 00 08 PARAMETER LIST BLOCK DESCRIPTER : 00 2c cf 11 00 00 02 00 OFFSET CURRENT DEFAULT SAVED CHANGEABLE 0 88 0a 00 00 88 0a 00 00 88 0a 00 00 88 0a ff 00 4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . 8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 PAGE : 38 PARAMETER LIST HEADER : 1b 00 00 08 PARAMETER LIST BLOCK DESCRIPTER : 00 2c cf 11 00 00 02 00 OFFSET CURRENT DEFAULT SAVED CHANGEABLE 0 b8 0e 10 00 b8 0e 10 00 b8 0e 10 00 b8 0e ff 00 4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . 8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== FORMAT MENU 1 Standard Format 2 Non-Standard Format 3 Bad Block Reassignment MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== NON-STANDARD FORMAT OPTIONS MENU 1 Edit Format Parameters 2 Edit Mode Sense Data 3 G-List Management 4 Begin Formatting the Disk MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT FORMAT PARAMETERS FORMAT-UNIT Command Block Bits FmtDat 1 CmpLst 0 Defect Header Parameters FOV 1 DPRY 0 DCRT 1 . STPF 1 DIVE Format Options Issue MODE SELECT Y Surface Analysis Y Use Edited G-List N DISK I/O-MAXTOR-ALL---------------------------------FIB027 Pg004 MAI Systems Corporation DIVE - BOSS/VX Disk Utility Rev 1.1C*01 Selected Device : 0s0 =============================================================================== EDIT SENSE DATA BYTE HEX BINARY COMMENT 0 00 0 0 0 0 0 0 0 0 Parameter List Header 1 00 0 0 0 0 0 0 0 0 2 00 0 0 0 0 0 0 0 0 . 3 08 0 0 0 0 1 0 0 0 4 00 0 0 0 0 0 0 0 0 Block Descriptor 5 2c 0 0 1 0 1 1 0 0 6 cf 1 1 0 0 1 1 1 1 7 11 0 0 0 1 0 0 0 1 . 8 00 0 0 0 0 0 0 0 0 9 00 0 0 0 0 0 0 0 0 10 02 0 0 0 0 0 0 1 0 . 11 00 0 0 0 0 0 0 0 0 12 01 0 0 0 0 0 0 0 1 Page 1 Start 13 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes 14 24 0 0 1 0 0 1 0 0 15 0e 0 0 0 0 1 1 1 0 16 16 0 0 0 1 0 1 1 0 . 17 06 0 0 0 0 0 1 1 0 18 02 0 0 0 0 0 0 1 0 19 00 0 0 0 0 0 0 0 0 20 00 0 0 0 0 0 0 0 0 21 00 0 0 0 0 0 0 0 0 . 22 00 0 0 0 0 0 0 0 0 23 00 0 0 0 0 0 0 0 0 24 02 0 0 0 0 0 0 1 0 Page 2 Start . 25 0e 0 0 0 0 1 1 1 0 Page Length : 14 bytes 26 01 0 0 0 0 0 0 0 1 . 27 40 0 1 0 0 0 0 0 0 28 00 0 0 0 0 0 0 0 0 29 00 0 0 0 0 0 0 0 0 30 00 0 0 0 0 0 0 0 0 31 00 0 0 0 0 0 0 0 0 32 00 0 0 0 0 0 0 0 0 . 33 00 0 0 0 0 0 0 0 0 34 00 0 0 0 0 0 0 0 0 35 00 0 0 0 0 0 0 0 0 36 00 0 0 0 0 0 0 0 0 37 00 0 0 0 0 0 0 0 0 38 00 0 0 0 0 0 0 0 0 39 00 0 0 0 0 0 0 0 0 40 03 0 0 0 0 0 0 1 1 Page 3 Start 41 16 0 0 0 1 0 1 1 0 Page Length : 22 bytes 42 00 0 0 0 0 0 0 0 0 43 13 0 0 0 1 0 0 1 1 . 44 00 0 0 0 0 0 0 0 0 45 06 0 0 0 0 0 1 1 0 46 00 0 0 0 0 0 0 0 0 47 00 0 0 0 0 0 0 0 0 . 48 00 0 0 0 0 0 0 0 0 49 00 0 0 0 0 0 0 0 0 50 00 0 0 0 0 0 0 0 0 51 65 0 1 1 0 0 1 0 1 52 02 0 0 0 0 0 0 1 0 53 00 0 0 0 0 0 0 0 0 54 00 0 0 0 0 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB027 Pg005 . 55 01 0 0 0 0 0 0 0 1 56 00 0 0 0 0 0 0 0 0 57 00 0 0 0 0 0 0 0 0 58 00 0 0 0 0 0 0 0 0 59 0c 0 0 0 0 1 1 0 0 60 40 0 1 0 0 0 0 0 0 61 00 0 0 0 0 0 0 0 0 62 00 0 0 0 0 0 0 0 0 63 00 0 0 0 0 0 0 0 0 64 04 0 0 0 0 0 1 0 0 Page 4 Start 65 16 0 0 0 1 0 1 1 0 Page Length : 22 bytes . 66 00 0 0 0 0 0 0 0 0 67 06 0 0 0 0 0 1 1 0 68 f2 1 1 1 1 0 0 1 0 . 69 13 0 0 0 1 0 0 1 1 70 00 0 0 0 0 0 0 0 0 71 00 0 0 0 0 0 0 0 0 72 00 0 0 0 0 0 0 0 0 73 00 0 0 0 0 0 0 0 0 74 00 0 0 0 0 0 0 0 0 75 00 0 0 0 0 0 0 0 0 76 00 0 0 0 0 0 0 0 0 . 77 00 0 0 0 0 0 0 0 0 78 00 0 0 0 0 0 0 0 0 79 00 0 0 0 0 0 0 0 0 80 00 0 0 0 0 0 0 0 0 81 00 0 0 0 0 0 0 0 0 82 00 0 0 0 0 0 0 0 0 83 00 0 0 0 0 0 0 0 0 84 0e 0 0 0 0 1 1 1 0 85 10 0 0 0 1 0 0 0 0 86 00 0 0 0 0 0 0 0 0 87 00 0 0 0 0 0 0 0 0 88 08 0 0 0 0 1 0 0 0 Page 8 Start . 89 0a 0 0 0 0 1 0 1 0 Page Length : 10 bytes 90 00 0 0 0 0 0 0 0 0 91 00 0 0 0 0 0 0 0 0 92 00 0 0 0 0 0 0 0 0 93 00 0 0 0 0 0 0 0 0 94 00 0 0 0 0 0 0 0 0 . 95 00 0 0 0 0 0 0 0 0 96 00 0 0 0 0 0 0 0 0 97 00 0 0 0 0 0 0 0 0 98 00 0 0 0 0 0 0 0 0 . 99 00 0 0 0 0 0 0 0 0 100 38 0 0 1 1 1 0 0 0 Page 38 Start 101 0e 0 0 0 0 1 1 1 0 Page Length : 14 bytes 102 10 0 0 0 1 0 0 0 0 103 00 0 0 0 0 0 0 0 0 104 00 0 0 0 0 0 0 0 0 105 00 0 0 0 0 0 0 0 0 106 00 0 0 0 0 0 0 0 0 107 00 0 0 0 0 0 0 0 0 108 00 0 0 0 0 0 0 0 0 . 109 00 0 0 0 0 0 0 0 0 110 00 0 0 0 0 0 0 0 0 111 00 0 0 0 0 0 0 0 0 112 00 0 0 0 0 0 0 0 0 113 00 0 0 0 0 0 0 0 0 114 00 0 0 0 0 0 0 0 0 115 00 0 0 0 0 0 0 0 0 DISK I/O-MAXTOR-ALL---------------------------------FIB027 Pg006 ORIGINATOR: Norm Jones DISK I/O-MAXTOR-ALL---------------------------------FIB027 Pg007 FIB 00028 MAI COMPANY CONFIDENTIAL 02/05/95 *** MXT 540S - 535MB 3 1/2", Jumper information. *** Maxtor MXT 540S - 504MB 3 1/2" This drive may be used in place of the LXT 535 in GPx 1130/1150/4150 as well as other systems. The following jumper information applies to the MXT 540S: --------------------------------------------------------------- | | -- | | | | 9 1 | -- |o||o| o o o | | |o||o| o o o J6 | | | -- | | | |S | | | |C | | |o| o o | |S |o| JP8 o o | | |o| o o | |I o o o o |o| o |o| o o JP5 | | o o o o |o| o J7 JP4 | | | -- | | | |_____________________________________________________________| |o| |o| = jumper installed Drive address is selected via jumper J6, pairs 1, 2, and 3: DRIVE ID# 1-2 3-4 5-6 ------------------------------------- 0 0 0 0 1 1 0 0 2 0 1 0 3 1 1 0 4 0 0 1 5 1 0 1 6 0 1 1 0 = jumper removed 1 = jumper installed Note: Drive ID #2 reserved for 1/4" tape drive on SCO Systems (1130/1150 4150/5150,etc). ORIGINATOR: Barry Matthews DISK I/O-MAXTOR-ALL---------------------------------FIB028 Pg001 FIB 00029 MAI COMPANY CONFIDENTIAL 10/23/95 *** TERMINATORS FOR 5 1/4" SCSI DRIVES *** SYMPTOM/TEXT: The 5 1/4" SCSI drives may require three terminators installed in specific configurations (on SPx systems or if they are the last device on a SCSI bus). The part number for terminatators for the 280/380/760 MB drives is YY030128. See FIB #15 in this category for location and orientation of terminators. ORIGINATOR: Barry Matthews DISK I/O-MAXTOR-ALL---------------------------------FIB029 Pg001